HID MOD001 Handbuch installieren - Seite 9

Blättern Sie online oder laden Sie pdf Handbuch installieren für Kontrolleinheit HID MOD001 herunter. HID MOD001 11 Seiten.

Seite drucken

Powering

Trusted Identities

4. Regulatory information

SRD Model: MOD001

RF Specifications

Standard protocol

BLE 4.2

Frequency band

2400-2483.5 MHz

No of RF channels

RF output power

+5 dBm

Modulation

GFSK

Antenna

PCB, 0.30 dBi

Communication Regulation

The following is a list that applies:

US FCC – United States Compliance

FCC ID: SL6-MOD001

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

IMPORTANT: Changes or modifications to this product not authorized by

HID, could void the FCC Certification and negate your authority to operate

this product.

Note: This equipment has been tested and found to comply with the limits for a

class B digital device, pursuant to part 15 of the FCC rules.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator & your body.

This module is certified pursuant to two Part 15 rules sections(15.247).

Integrator / End Product

The user manual of the end product should include:

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated

with minimum distance 20cm between the radiator and your body.

Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this

equipment.

Label of the end product:

The host product must be labeled in a visible area with the following

"Contains FCC ID: SL6-MOD001".

The end product shall bear the following 15.19 statement: This device

complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference

that may cause undesired operation.

PLT-06387, Rev. A.0

Canada Compliance

24824-MOD001

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may

not cause interference, and (2) this device must accept any interference,

including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables

aux appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et

(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limits set forth

for an uncontrolled environment. This equipment should be installed and

operated with minimum distance 20cm between the radiator & your body.

Cet équipement est conforme aux limites d'exposition aux rayonnements

IC établies pour un environnement non contrôlé. Cet équipement doit être

installé et utilisé avec un minimum de 20cm de distance entre la source de

rayonnement et votre corps

OEM integrator is still responsible for testing their end product for any

additional compliance requirements required with this module installed (for

example, digital device emissions, PC peripheral requirements, etc.).

IMPORTANT NOTE: In the event that these conditions cannot be met

(for example certain laptop configurations or co-location with another

transmitter), then the IC authorization is no longer considered valid and the

IC number can not be used on the final product. In these circumstances,

the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate IC authorization.

OEM Integrator Notice

End Product Labeling

This transmitter module is authorized only for use in device where the

antenna may be installed such that 20 cm may be maintained between the

antenna and users. The final end product must be labeled in a visible area

with the following: "Contains transmitter module IC: IC: 24824-MOD001".

Contient le module d'émission IC: IC: 24824-MOD001

The Host Model Number (HMN) must be indicated at any location on the

exterior of the end product or product packaging or product literature which

shall be available with the end product or online.

This device is intended only for OEM integrators under the following

conditions:

1. The antenna must be installed such that 20cm is maintained between the

antenna and users, and

2. The transmitter module may not be co-located with any other transmitter

or antenna.

Cet appareil est conçu uniquement pour les intégrateurs OEM dans les

conditions suivantes: (Pour utilisation de dispositif module)

1. L'antenne doit être installée de telle sorte qu'une distance de 20cm est

respectée entre l'antenne et les utilisateurs, et

2. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur

ou antenne.

Australia/ New Zealand Compliance

This product conforms to Australia and New Zealand Radio Requirements.

Japan

217-220435

UK Compliance

HID® MOD001

Install Guide

January 2022