Gaines Janzer Post Installation & Assembly - Seite 2

Blättern Sie online oder laden Sie pdf Installation & Assembly für Postausrüstung Gaines Janzer Post herunter. Gaines Janzer Post 2 Seiten.

Attach the Arm Clip to the post with two screws using the two lower center holes on post face.

The slot on the Arm Clip should be on the bottom. Do not over tighten. Now attach the Post Arm

by sliding it over the Arm Clip, with the short side of the Post Arm against the post. Push down

firmly until the Post Arm is flush with the post. (Note: If the Post Arm will not start over the top

of the clip, you can use a pair of pliers to slightly bend the top of the clip away from the post until

the Post Arm fits over the Arm Clip in a snug manner.)

Now attach the Finial to the top of the post. The square base of the Finial will press fit into the

open square top of the post. If desired, apply clear exterior silicone adhesive (available at your

local hardware store) to the inside walls of the post before inserting the Finial.

At this point, please follow the instructions included with your Janzer Mailbox to attach the

mailbox to the post.

B. Side Mount Option - If this option is used the hole will generally be 16"-18" from face of post to

street. Once the desired post spot is determined, dig a 12" diameter hole to the depth needed. The

depth of the hole will depend on your desired height of mailbox. Place the post into the hole with

threaded holes on the post facing the side you intend to mount the mailbox on (usually on the right

side as you face the post from the street). The top of the post is the end that the holes on the post

are closest to. Use a spirit level to set post to true vertical position in the post hole. Be sure to align

the face of the post with the driveway, sidewalk, walkway, roadway, etc. Pour concrete completely

around the post, taking care to maintain the level of the post. Cover concrete with top soil if

desired. If you are installing a Decorative Cuff (accessory sold separately) please follow the

instructions with the Cuff at this point. Once completed, please continue with these instructions.

Attach the Arm Clip to the post with two screws using the two lower center holes on post face.

The slot on the Arm Clip should be on the bottom. Do not over tighten. Now attach the Post Arm

by sliding it over the Arm Clip attached to post, with the long side of the Post Arm against the

post. Push down firmly until the Post Arm is flush with the post. (Note: If the Post Arm will not

start over the top of the clip, you can use a pair of pliers to slightly bend the top of the clip away

from the post until the Post Arm fits over the Arm Clip in a snug manner.) Push down firmly

until the Post Arm is flush with the post.

Now take the Side Mount Plate and set it on top of the Post Arm, lining up the slots on the bottom

(center) with the holes on the Post Arm, and lining up the slots on the short angle side with the

holes in the post. Take two of the Phillips screws and put them through the Screw Cover

Retainers and start them loosely into the post. Take two more Phillips screws with fender washers

and start them loosely into the Post Arm. Tighten all four screws securely (do not over-tighten).

Put Screw Covers over the Screw Cover Retainers on the post.

Now attach the Finial to the top of the post. The square base of the Finial will press fit into the

open square top of the post. If desired, apply clear exterior silicone adhesive (available at your

local hardware store) to the inside walls of the post before inserting the Finial.

At this point, please follow the instructions included with your Janzer Mailbox to attach the

mailbox to the post.

Thank you for purchasing this product. Should you have any questions, please call Gaines Customer Service at 858-486-7100.

Gaines Manufacturing, Inc.

San Diego, CA

www.gainesmfg.com

Page 2 of 2