Hideaway Deluxe KK12D Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Inneneinrichtung Hideaway Deluxe KK12D herunter. Hideaway Deluxe KK12D 2 Seiten.

Seite drucken

INSTALLATION INSTRUCTIONS START HERE

Step 1 - Separate the runner components (see Fig 2a & 2b)

• Place the mounting panel upside down on a flat surface with the runners facing upwards.

• Fully extend the runners.

• Find the black levers located on the outer side of both the left and right runner.

• Simultaneously, push the left lever down and the right lever up and pull inner of the runners towards you until it separates completely

from the unit. Set runner inner with collar, handle/door bracket attached aside in a safe location.

• Push the outer runners attached to the mounting panel back inside the unit.

Step 2 - Remove the friction-fitted lid from mounting panel (see Fig 3a, 3b & 3c)

• Mounting panel should still be upside down on a flat surface with the runners facing upwards.

• To remove the friction-fitted lid - push firmly down on the lid at the back of the unit.

• Push firmly, distributing pressure to both sides of lid to ensure the lid clears the hooks located on the left and right hand sides of

the mounting panel (fig 3b).

• Simultaneously, pull the friction-fitted lid forwards until it clears the mounting panel (fig 3c).

• Pull the foam pad clear of the mounting panel. Set aside, leaving the plastic cover on.

Step 3 – Predrill the Carcase

• Refer to the Installation Dimensions on the back page of these instructions.

• Mark out the mounting positions to be used and drill a 2mm hole 10mm deep at each point.

Step 4 – Installing the Mounting Panel in the Carcase

• Position the mounting panel within the carcase.

• Use the 16mm Surefix screws and the washers in top mount locations.

• Use the 16mm Surefix screws in side mount locations. Note: A #1 Square Drive or #2 Phillips Drive bit may be used.

Step 5 - Reinstall the friction-fitted lid and foam into mounting panel

• Rest the foam on top of the friction-fitted lid - the flat side of the friction-fitted lid should be towards the ground with the folds facing upwards.

• Slide the friction-fitted lid and foam inside the mounting panel, stopping just before the rear hooks. (Note: the large fold on the friction-fitted lid sits at

the front of the unit, and the rear of the lid has the slots which reconnect with the hooks located on the mounting panel at the rear).

• Simultaneously, with one hand, push firmly up on the back of the friction-fitted lid, push the lid above the hooks and drop into location. Whilst this is

happening, with the other hand push the front of the lid upwards to ensure it rests on the metal support - located at the front of the mounting panel

(fig 3c).

• The lid should move up and down slightly, with ease indicating correct installation.

Runners engaged - push left lever down

Top and/or side mounting points

and right lever up

Friction-fitted lid

Mounting

panel

Runners

Liner holder

Runner Outer

Bucket

FIG 1 - Bin Parts

FIG 2a - Removing Runners

Runners disengaged - pull the runner inner

clear of the outer

Runner Outer

Runner Inner

Pull the inner runner out until it separates

from the unit

Black lever on runners

FIG 2b - Removing Runners

Step 6 – Predrilling the Door Panel (Door Pull Models Only)

• Mark a vertical centre line down the rear of the door panel.

• Mark the overlay at the top of the door panel.

• With reference to the Installation Dimensions mark the D2 Door Mount positions.

• Drill a 2mm hole 10mm deep at each of the marked positions.

Step 7 – Mounting and Adjusting the Door Panel (Door Pull Models Only)

• Position the door bracket on the door panel and align with the predrilled holes.

• Secure the door bracket using a 12mm Surefix Screw in each of the 2 vertical slots.

• Reattach the runner inners – Refer to FIG 2.

1. Ensure the runner outers attached to the mounting panel are pushed as far as they will go into the unit.

2. Ensure the runner inners are as far forward as they will go.

3. Line up the runner inners (with the collar handle/door bracket attached) to the runner outers.

4. Push the runner inners into position until the unit is fully closed. There may be some resistance when pushing the unit closed but

the runner should operate smoothly after reassembly.

• Adjust the angle of the door panel by loosening the two M6 nuts and bolts, moving the door bracket so it is parallel with the carcase and

retightening the M6 nuts and bolts.

• Adjust the vertical position of the Door Panel by loosening the 2 Surefix Screws in the vertical slots and moving the panel as required.

• Drill a 2mm pilot hole 10mm deep at the centre of each of the horizontal slots.

• Secure the door panel using 12mm sure fix screws through the 4 horizontal slots.

• If required adjust the horizontal position of the door panel by removing the 2 screws in the vertical slots, loosening the screws in the horizontal

slots, adjusting the panel position and retightening the screws in the horizontal slots.

• Reinstall the 2 screws into the vertical slots. Additional pilot holes may need to be drilled.

Step 8 - Place bin bucket/s into checkouts on collar

• Fully extend the runners.

• Place bucket/s into the checkouts provided on the collar of the unit. If the bucket/s do not sit within these checkouts the unit will

not close properly.

• Please leave the Care and Maintenance Instructions inside the bucket for the owner.

Runner Inner

Push firmly on the back of the unit to ensure the

lid clears the hooks located on the right and left

hand sides of top mounting panel

FIG 3a

Hook

Metal support

Lid coming free

of hook

The unit should look like this with the friction

fitted lid and and foam pad removed

FIG 3b

FIG 3c