Hidro-Water ZENIT Handbuch für Benutzer und Installateure - Seite 7
Blättern Sie online oder laden Sie pdf Handbuch für Benutzer und Installateure für Water Filtration Systems Hidro-Water ZENIT herunter. Hidro-Water ZENIT 15 Seiten. Residential reverse osmosis
Seite drucken
i.
Raise the arm of the WATER STOP leak detector
and place a piece of absorbent material
(Figure-14) as indicated in the picture. Put
away the other piece to use as a spare. Lower
the arm so that water can enter the osmosis
system.
j.
Once it runs clear, turn the faucet off.
k. Replace the right-hand-side cover of the ZENIT osmosis system (looking the
system from the front). Screw it on with the corresponding screws. Then replace
the protective caps.
l.
The system is now ready for us.
CONGRATULATIONS! YOUR SYSTEM IS ALREADY FULLY INSTALLED AND RUNNING
6.- USER INTERFACE
The ZENIT osmosis system has a user interface system, made up of 3 LEDS, which
will inform you of the system's status at all times. It will also inform you when the cartridge
or membranes need to be changed and if there is any leak.
a. LED 1: WORKING AND LOW PRESSURE/LEAK DETECTOR
̵
This LED will be Green when the system is producing water.
̵
This LED will be flashing red when there is a water leak or if there isn't enough
pressure. The system will make a noise for 30 seconds every 8 hours.
12
MA-ES-RO-ZENIT_RO-0236-02_FL_20_V02
LED 2 STANDBY
b.
̵
This LED will be Green when the system is not working.
̵
This LED will be off when the system is working.
c. LED 3: TDS DETECTOR / FILTER CHANGE
̵
This LED will be Green when the water's TDS is correct.
̵
This LED will be flashing Green when the water's TDS isn't correct. The system
will make a noise for 30 seconds every 8 hours. (In this case you must contact
your distributor).
̵
This LED will be red 15 days prior to having to change the cartridges. This LED
will be flashing red on the day you should change the cartridges. The system
will make a noise for 30 seconds every 8 hours. (In both cases you must contact
your distributor).
̵
If 15 days after the day of needing changed, the cartridges haven't been
changed, the system will stop producing water.
7.- INSTRUCTIONS & MAINTENANCE
The installer should inform the family members of the following points of the
Reverse Osmosis System:
a. Location of the water inlet, faucet, WATER STOP leak detector, drain clamp and the
plug that connects the osmosis system to the mains supply.
b. Uses for purified water (cooking, to make coffees & teas, drinking, ice cubes, ironing,
fish tanks...).
c. Maintaining the osmosis system. The recommended maintenance of the osmo-
sis system is in the table below. By not following the maintenance as described
in this manual, using original cartridges and by authorized per-sonnel that
guarantees the quality of the water produced and the correct operation of the
osmosis system, the warranty will be void.
Cartridge type
Carbon GAC cartri-
Carbon CTO cartrid-
dge
Stage
1ª
Reference
CA-9006-04
CA-9006-05
Appearance
Replace*
6 - 9 months
6 - 9 months
Sanitation
Every time you change a cartridge, the membranes or a component in
contact with water or if you do not have consumed water in over a month,
you must sanitise the system using the Sanitising kit (OI-0207-131). Not
supplied with the system
.
MA-ES-RO-ZENIT_RO-0236-02_FL_20_V02
Membranes
Postfilter
ge
2ª
3ª y 4ª
5ª
ME-2003-06
OI-0205-18
2 – 3 years**
12 months
13