dB Technologies VIO S118R Schnellstart-Benutzerhandbuch - Seite 3
Blättern Sie online oder laden Sie pdf Schnellstart-Benutzerhandbuch für Subwoofer dB Technologies VIO S118R herunter. dB Technologies VIO S118R 4 Seiten.
Seite drucken
3) First switch-on
The DIGIPRO G4 amplifier of VIO
a powerful DSP. All the connections and controls
the rear amplifier control panel:
The subwoofer is supplied with a mounted fuse for
operation within the 220-240V~ range. If you need to
operate in the 100-120V~ voltage range:
Disconnect all connections, including the power
supply
Wait 5 minutes
Replace the fuse with the one provided in the
package for the 100-120V~ range
1 – Input (balanced) connector
2 – Link/Xover Out (balanced) connector
3 – Subwoofer attenuation rotary control
VIO S118R
www.dbtechnologies.com info@dbtechnologies‐aeb.com
S118R is controlled by
are in
4 – Delay rotary controls
5 – Polarity switch
6 – Cardioid preset switch
7 – Link/Xover Out switch
8 – Xover LPF
9 – Status LEDs (Limiter, Signal, Mute/Protection,
Ready)
10 – RDNet Data In
11 – RDNet Data Out
12 – RDNet status LEDs
13 – System test switch
14 – USB Data Service (USB-standard Type B)
15 – Full Range Mains input connector
16 – Mains Link connector
17 – Mains Fuse
a) Once you have properly set up the desired
configuration (see also the VIO S118R complete user
manual and accessories instructions for further
information), connect the audio input (1). Set the
Subwoofer attenuation (3) to 0 dB.
b) Connect the possible output direct link (2), and set
the
Link/Xover Out
switch (7). If your choice is Xover,
you can choose the LPF frequency with (8) Xover
rotary. This filter does not affect the "Link" output.
c) Choose the Subwoofer Setup (Delay 4, Polarity 5)
In cardioid configuration, please note that the
cardioid preset switch (6), when active, bypass these
controls.
d)
In case of remote control, connect the Data Input
(10) to the hardware remote controller (RDNet
Control 2 or RDNet Control 8) with cables equipped
with etherCON connectors. Then connect the Data
Output (11) to the Data Input (10) of a possible
second device, and so on. When the RDNet network
is on and it has recognized the connected device, the
LED "Link" (12) is on. The other LEDs (12) "Active"
start blinking at the presence of data transmission,
the "Remote Preset Active" advise that all the local
controls set on the amplifier panel (level, DSP
presets, etc.) are by-passed and controlled remotely
by RDNet. In remote control it is essential the use of
free dBTechnologies software (check the last revision
on
www.dbtechnologies.com
AURORA NET,
necessary for an in-depth control of different devices
in remote connection;
dBTechnologies Composer,
necessary for safety check and for the complete
sound system design, particularly developed for VIO
series.
e)
Connect the power supply (15). Link the power to
other subwoofer or modules (see Technical Data for
further information) using mains link connector (16).
Check the complete user manual on
information about the system and available accessories.
Scarica il manuale completo da
ulteriore informazione sul sistema e sugli accessori disponibili.
Für weitere Informationen und verfügbares Zubehör lesen sie bitte die
vollständige Bedienungsanleitung unter
www.dbtechnologies.de.
Vérifiez le manuel de l'utilisateur complet sur
pour des informations complémentaires du système et des accessoires
disponibles.
Compruebe
el
manual
www.dbtechnologies.com
para la información adicional sobre el sistema y
accesorios disponibles.
Rev 1.2 cod. 420120271Q
):
www.dbtechnologies.com
for further
www.dbtechnologies.com
per ogni
www.dbtechnologies.com
de
usuario
completo
sobre