Gakken Japanino Zusammenbau, Gebrauchsanweisung - Seite 4

Blättern Sie online oder laden Sie pdf Zusammenbau, Gebrauchsanweisung für Computer Hardware Gakken Japanino herunter. Gakken Japanino 5 Seiten. 8-bit micro computer

Seite drucken

How to Use the Supplement

Preparation

Installing Software Required

(Before installing, check the following for the PC you are using)

●Check the OS of the PC you are using.

→All of the software programs you need are compatible with the Windows XP (SP2 or later), Vista, Windows 7/Mac OS X10.4 or later

operating systems.

●Do you have a USB 2.0 port for the interface?→ If not, you will not be able to use the supplement.

●Do you have at least 200 MB of free space available on your hard disk drive? → If not, you will not be able to use the supplement.

●Please reorganize, etc. your hard disk drive to free up disk space.

* Please start the install procedures after checking the items given above.

Connect to the Internet, and download IDE ("Arduino 0018" ) and

Driver Soft from the below and install them on your PC.

● Japanino webpage

http://otonanokagaku.net/english/japanino/

Check that the driver files installed correctly with the IDE screen.

For Windows

1) Open the IDE.

2)Open the [Board] folder from [Tools] and select [Arduino Pro

Mini (3.3V,8MHz)w/ATmega168]. The mark will appear next to

the selected item.

3) Insert the Japanino into the USB port on your PC.

4) Open [Serial Port] from [Tools] in the IDE, and write down the

number from [COM ].

5) Open [Serial Port] from [Tools] in the IDE, and select the

checkbox for the number of the COM that was just added (it

may take some time for the new COM number to appear in

some cases).

O tona

Kagaku

For Mac

1) Open the IDE.

2) Insert the Japanino into the USB port on your PC.

3) Open the [Board] folder from [Tools] and select [Arduino Pro

Mini (3.3V,8MHz)w/ATmega168]. The mark will appear next to

the selected item.

4) Open [Serial Port] from [Tools] in the IDE, and select [/dev/tty.

SLAB_USBtoUART].

* If using a USB port that you do not usually use, there

are cases where it may not function properly due to

being affected by dust or dirt. If the COM port cannot

be seen, remove the Japanino from the USB port and

remove any dust or dirt from the port before trying to

reinsert it.

IMPORTANT

Please note that it is extremely important that you

confirm that the COM port number assigned for the

Japanino is the same on the PC and in the IDE and that

the IDE recognizes that " the connec ted Micro

Computer is a Japanino." If this is not done, you will not

be able to upload sketches (programs) to the Japanino.

Please make sure to confirm that this is done. If using

two or more Japanino units, you will need to check the

COM port numbers for each when inserting them into

the PC as they will each be assigned to a different COM

port.

Basics for How to Use an IDE

What an "IDE" is...The Japanino itself is nothing more than a simple device that is a hardware unit and cannot receive commands to be used

to control something as a computer. To use the Japanino, you will need software for writing sketches (programs) and for writing data. An

"IDE" is used with the Japanino.

Verify

Verify that a written sketch will work properly.

This is referred to as "Compile" (which means,

"translating a written sketch into machine

language") in the terms used in Arduino.

Stop

New

Open

Save

Upload to Micro Computer board

Transmit the uploaded sketch to the circuit

board.

Space for displaying details of operations

and their results.

Space for displaying messages, such as error

messages, etc. from the IDE side

How to Use the Supplement

Space for

drawing

sketches