Autometers Systems IC 970 Installations- und Betriebshandbuch - Seite 12

Blättern Sie online oder laden Sie pdf Installations- und Betriebshandbuch für Messgeräte Autometers Systems IC 970 herunter. Autometers Systems IC 970 12 Seiten.

Seite drucken

Autometers Systems IC 970 Installations- und Betriebshandbuch

Functions

Supplied

Function 09 -

Min/Max Volts

Function 10 -

Min/Max Amps

As Standard

Function 11 -

Min Max Neutral Amps

Function 12 -

Peak Maximum Demand

Function 13 -

C.T and N.T current transformer setting

Function 21 -

Pulse value

Function 22 -

Pulse Duration

Function 30 -

Display contrast

Function 31 -

Back light Duration

Function 50 -

Connection details

Function 51 -

Relay test mode

Function 52 -

Binar y switch positions

Physical

Dimensions (mm)

W96mm x H96mm x D 89mm (with comms module 103mm). Weight with communication module

and ﬁxing clips: 0.64 k ilos. Pack ing weight individually boxed in polyfoam box: 0.65 k ilos

Maintenance and service

Field Service Considerations

In the unlikely event that a unit should fail, it will generally be ser viced by exchanging the unit

for a replacement unit. The initial installation should be done in a way which makes this as

convenient as possible.

1. I t is good practice that a current transformer shor ting block is ﬁtted, this enables the meter to

be disconnected without open circuiting the current transformers. The shor ting block should be

wired so that the protective relays are not aﬀected.

2. All wiring should be routed to allow easy removal of the connection to the terminals.

Disconnect From Supply

A suitable isolator for both voltage and current terminals shall be included in the wiring

installation, close to the meter with easy access and marked as the meters disconnect device.

If the equipment is used in a manner not speciﬁed by the manufacturer the protection provided

by the equipment may be impaired. Current measuring terminals are not intended to be

connected to voltages to ear th above 50Vac.

Per formance Characteristics - Typical load cur ve with balanced load at 50 Hz

0.4

0.3

0.246

0.223

0.189

0.2

0.102

0.1

0.068

0.048

Reset to Zero

Programmable

View only

Pf 0.5L

Pf 1.0

0.105

0.069

0.055

0.046

Amps

Dedicated customer service

Customer care is the cornerstone of the company 's success. A positive ser vice policy is obser ved

throughout ever y specialist area of operation.

The personal involvement of all the directors at ever y level, a highly trained and motivated staﬀ,

fully computerised systems and in depth stock holding combine to provide a level of ser vice

which has earned the appreciation of customers across the spectrum of the UK and overseas

markets. Computerised distribution systems are geared to a consistent 24 hour despatch of

products, with 20 minute despatch being possible in response to urgent demand for small orders.

Product range

Metering and monitoring equipment ranges from single phase and Polyphase kWh

electromechanical meters to a sophisticated range of fully programmable information centres.

Also available are Electronic Meters, Panel Mounted Meters, Maximum Demand Meters, DIN Rail

Meters and Current Transformers.

CE Approval.

The IC 970 has been fully examined and tested in accordance with the standards listed and meets

the speciﬁed requirements deﬁned in BS EN 61326:1997 inc A1, A2, A3 - Electrical equipment for

measurement, control and laborator y use - EMC requirements.

1. BS EN 61326:1997 inc. A1, A2 & A3

2. BS EN 61326:1997 inc. A1, A2 & A3

3. BS EN 61000-4-2:1995 inc. A1 & A2

4. BS EN 61000-4-3:2002 inc. A1 & A2

5. BS EN 61000-4-4:1995 inc. A1 & A3

Safety Standards: BS EN 61010-1:2001

Impor tant.

The attention of the speciﬁer, purchaser, installer or user is drawn to special measures and

limitations to use which must be obser ved when these products are taken into ser vice to

maintain compliance with the CE directives. Details of these special measures and limitations

of use are available from HMSO.

REF: IEC 1000-5-1(BS195/210788DC) IEC 1000-5-2 (BS 195/214642DC)

IEC 10000-5-6 (BS 195/210789DC).

WARNING DO NOT MEGGAR TEST

Conducted Emissions

Radiated Electricity Field Emissions

Electromagnetic Compatibility