Autonics ADS-SE1 Series Produkthandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Produkthandbuch für Zubehör Autonics ADS-SE1 Series herunter. Autonics ADS-SE1 Series 3 Seiten. Automatic door side sensors

Seite drucken

Cautions during Installation

• Install the unit correctly with the usage environment, location, and the designated

specifications.

• When installing over the two door sensors closely, it may result in malfunction due to

mutual interference. Do not change the position of the head of emitter and receiver.

Keep the installation distance between the two heads more than 50 cm.

• This product is for indoor only.

Avoid the place where the receiver is exposed to direct sunlight, or the ambient

illumination is in over the rated value.

• Do NOT impacts with a hard object or excessive bending of the wire lead-out. It may

cause damage the water resistance

Recommended Installation for the Sensor

1. Refer to the below and drill the holes on the side pillars of the auto door

for the installation.

• Check the mounting holes of the head of the emitter and receiver are in parallel for the

optical axes

• Grind around the mounting holes drilled smoothly.

It may hurt by sharp parts and cause malfunction by the inclined sensor head.

Through hole for sensor head

Using

the bracket

Fixing screw hole for bracket

Mounting hole for sensor head

Not using

the bracket

Panel thickness for sensor head 1.5

2. Mount the sensor heads to the mounting holes.

• It may cause malfunction because the sensitivity setting is not available as the optical

axes are not matched if the sensor body is inclined.

• Check the damage such as scratches or pollutant on the lens of the sensor head.

It may cause malfunction in the condition of interrupted light or lack of sensitivity by

dust.

• Be sure to use the mounting brackets of the one push method for the sensor with the

head holder and nuts. In the one push method, check the nuts are fixed on the sensor

body tightly.

Install the sensor with no gap between the nut and the side of the door or panel.

• Be sure to use the mounting brackets of the screw method for the sensor without the

head holder and nuts.

Install the sensor with no gap between the panel and the sensor.

One push method

Install the sensor head to the bracket

first and fix the bracket to the desired

place by the screws.

Using

the bracket

M4 flat

head screw

Through hole for

Bracket

sensor head

: Ø 13 to 14 mm

Put the sensor head into the mounting hole.

Not using

the bracket

■ Cautions during installation

• The rated sensing distance is max. 10 m (A).

Install the sensors within the rated sensing distance.

• Install the sensor with more than 50 cm (B) gap from

the bottom and ceiling. It may cause malfunction by

reflected beams from the surface of the bottom and

ceiling.

• Do not put obstacles between the emitter and

receiver. Otherwise, it may result in malfunction

Product Components

• Sensor: ADS-SHP (1 set - emitter and receiver)

• Fixing bolt for the controller (M4×20) × 2

Sold Separately

• Mounting bracket: ADS-SB12 (one push method)

• Mounting bracket: ADS-SB10 (screw method)

• Sensor: ADS-SHP (1 set - emitter and receiver)

• Controller: ADS-SEC

One push method Screw method

Ø 13 to 14 mm

M4 Tap or Ø 3 mm

Ø 12.2

M10 × 0.75 mm

±0.1

1.5

±0.5

Screw method

Remove the nut and head holder from

the sensor head first. Install the sensor

head to the bracket and fix the bracket

on the side pillar of the door by the

screws.

Screw hole:

M4 Tap or

①

Ø 3.5 mm

②

Nut

Through hole for

Head holder

sensor head

Bracket

: Ø 13 to 14 mm

[Fig. 1]

Recommended Installation for the Controller

1. Refer to the figure at the right side and adjust

the length of wires.

• Cut off the wires as much as your need and take off

the cover of them. Twist the end of the wires shown

in the figure, and connect to the controller.

It is easy to connect if soldering the end of the wires.

• Be sure to connect the wires in power OFF.

• Follow the figure when cutting off the wires of the

sensor head. If taking off the cover too much, it may

cause damage to this product as the end of both

wires are in contact with each other.

2. Match wires in the number of terminals and connect them.

• Do not connect the extended wire to the sensor.

It may cause malfunction by the noise.

• Do not connect 2 wires or more to the 1 terminal.

ADS-SE1

Output

Emitter

Receiver

(N.O.)(N.C.)

(gray)

(blue)

Power

(12-24 VACᜠ / VDCᜡ)

■ Connection for sensor / power / output wirings

• Press the wiring connection buttons and connect

the wires.

• It does not operate normally if the wires are

connected conversely. Before the wiring, be sure to

check the proper positions of the wires.

• Make sure that the power wire connects to the

power terminal (4, 5). Otherwise, it may cause

damage to this product.

• Allowable diameter: in case of the power and output

line

- Single and stranded wire: 0.2 to 1.5 mm

■ Cautions during installation

• Fix a controller with offered 2 fixing bolts.

Process the fixing holes of a controller by M4 and see the ' Dimensions' for the position

of holes.

• Do not over tighten the bolts when fixing the controller. The fixing holes may be

broken.

Specifications

Model

ADS-SE1

Available sensor sets

1 channel

Sensing distance

0 to 10 m

Sensing target

Opaque materials

Min. sensing target

≥ Ø 20 mm

Sensing method

Through-beam type

Response time

≈ 50 ms (from interrupted light)

Output holding time

≈ 500 ms (from received light)

Light source

Infrared LED (850 nm modulated)

Indicator

OUT 1 indicator (red), OUT 2 indicator (green)

Approval

ᜢ ᜫ

Weight (packaged)

≈ 300 g (≈ 450 g)

Power supply

12 - 24 VACᜠ ± 10 %, 50 / 60 Hz / 12 - 24 VDCᜡ ± 10 % (ripple P-P: ≤ 10 %)

Power consumption

AC: ≤ 2 VA / DC: ≤ 50 mA

Control output

Relay contact output

Relay contact capacity

50 VDCᜡ 0.3 A (resistive load)

01)

Relay contact composition

Relay life cycle

Mechanical: ≥ 5,000,000 times, electrical: ≥ 100,000 times

≥ 20 MΩ (500 VDCᜡ megger)

Insulation resistance

1 mm double amplitude at frequency of 10 to 55 Hz (for 1 minute) in each X, Y, Z

Vibration

direction for 2 hours

Shock

500 m/s² (≈ 50 G) in each X, Y, Z direction for 3 times

Ambient illumination

Sunlight: ≤ 100,000 ㏓

(receiver)

Ambient temperature

-20 to 55 ℃, storage: -25 to 60 ℃ (no freezing or condensation)

Ambient humidity

35 to 85 %RH, storage: 35 to 85 %RH (no freezing or condensation)

Protection structure

IP30 (IEC standard)

Connection

Cable connector type

Sensor cable

Ø 2.4 mm, 1-wire, 5 m

Wire spec.

AWG26 (0.16 mm, 7-core), insulator outer diameter: Ø 1.32 mm

Material of the controller

Housing: ABS, cover: ABS, bolt: SCM (brass, Ni-plate)

Material of the sensor

Holder: ABS, lens: PMMA, lens guide: PC, nut: PC

01) Do not use the load which is beyond the rated capacity of contact point of relay.

It may cause bad insulation, contact fusion, bad contact, relay breakdown, and fire etc.

17 mm

Outer shield wire

Inner covered wire

9 mm

ADS-SE2

① ②

①

②

Output

(N.O.)(N.C.)

Emitter

Receiver

(gray)

(blue)

Power

(12-24 VACᜠ / VDCᜡ)

ADS-SE2

2 channels