2GIS 2GIG-SDS1-345 Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Zubehör 2GIS 2GIG-SDS1-345 herunter. 2GIS 2GIG-SDS1-345 4 Seiten. Smoke detector sensor

Seite drucken

WALL ACCESS HOLE

SMOKE

DETECTOR

SENSOR

Figure 5. Install Smoke Detector Sensor between Wall and Moun ng Bracket

Place the smoke detector sensor where the exis ng moun ng bracket was

located. Make sure the wire/wiretaps are inserted through the center opening of

the smoke detector moun ng bracket.

Place the exis ng smoke detector moun ng bracket on top of smoke detector

sensor. Align the smoke detector sensor and the smoke detector moun ng

bracket and replace the two screws used to hold the bracket in place. Tighten all

screws down.

✓ NOTE: It is suggested that the smoke detector sensor LEDs be oriented towards

the bo om or in a manner that allows the LEDs on the unit to be visible.

EXISTING

POWER

PIGTAIL

MOUNT BRACKET

WITH LED'S AT BOTTOM

Figure 6. Wiretaps/Wires, & Pigtail through Center

1. PLACE WIRE

INTO

WIRETAP.

Figure 7. Crimping Wiretaps onto Wires

YEL/YEL OR

YEL/ORANGE

EXISTING

WIRETAPS (3)

POWER

CRIMPED

PIGTAIL

TO PRIMARY

CIRCUIT WIRES

Figure 8. Wiretap Connec ons

EXISTING

POWER

PIGTAIL

WIRETAPS (3)

(NOT CONNECTED)

EXISTING SMOKE DETECTOR

MOUNTING BRACKET

SMOKE

DETECTOR

SENSOR

EXISTING

SMOKE

DETECTOR

MOUNTING

BRACKET

WIRETAPS (3)

(NOT CONNECTED)

2. HINGE WIRETAP

UP AND OVER

WIRE STRAND

3. CRIMP

WIRETAP WITH

PLIERS

PRIMARY POWER

WIRING

BLK/BLK (110VAC)

WHT/WHT (NEUTRAL)

WIRING CODE:

• BLACK TO BLACK (120 VAC)

• WHITE TO WHITE (NEUTRAL)

• YELLOW TO YELLOW OR

ORANGE (INTERCONNECT)

Wiring the Connections

Before connec ng the wires from the smoke detector sensor, iden fy the (+) line

(hot) 120VAC wire and the neutral wire. Usually the (+) line (hot) 120VAC wire

will be black and the neutral wire white. Use a voltmeter or voltage sensor to

verify that the proper wires are selected. You may need to reconnect power to the

electrical circuit powering the interconnected hardwired smoke detectors in order

to do this (Figure 8).

WARNING: Remember to disconnect or shut oﬀ electrical power to the

interconnected hardwired smoke detector if it was powered on in the previous

step to iden fy the 120VAC wires.

Use an electrician's linesman plier or equivalent tool (See Figure 8) and using the

installed wiretaps on the device, crimp the wiretap with the black wire onto the

120VAC line (hot) wire.

✓ NOTE: Wiretaps must be used on a sec on of stranded wire. This is typically

located between the connector to the smoke detector and the wire nut.

The wiretap with the yellow wire should be a ached to the wire lead connected

to the interconnect wire of the smoke detector. This wire is typically yellow or

orange.

Once all (3) three wiretaps have been installed (Figure 8), rea ach the electrical

wire pigtail to the back of the smoke detector unit and mount the smoke detector

on the moun ng base (Refer to Figure 3).

Installing the Back-Up Battery

MOVE TO

FRESH AIR

First Alert

SMOKE AND CARBON

MONOXIDE ALARM

SMOKE

Figure 9. Installing Back-up Ba ery

WARNING: Ensure that the smoke detector sensor has been wired correctly.

Damage to the smoke detector sensor may occur if the 120 VAC line (hot) wire

neutral wire are reversed. The unit may fail to func on properly if incorrectly

wired.

Turn on or reconnect power to the primary electrical circuit that powers the

interconnected hardwired smoke detector system. The device should now power

on.

Use a ﬂ at bladed tool, slide out the ba ery tray that holds the backup ba ery.

Insert a CR2032A ba ery (included) into the ba ery slot. Slide the ba ery tray

back into the device (Figure 9).

✓ NOTE: Orient the (+) ba ery terminal up so that it is visible when facing the unit.

Programming the Sensor

Follow the instruc ons on how to program a sensor into a compa ble 2GIG control

panel. See the 2GIG control panel's Installa on & Programming Guide for more

informa on on how to learn a sensor into the control panel.

The device should learn in as a Loop 1 sensor device. Use a small paper clip or other

sharp object and carefully insert into the learn/test bu on hole. This will send

out an alarm transmission ID so the the sensor can be learned into a compa ble

control panel or can be used to test that the transmi er is working properly.

Replacing the Battery

If the compa ble control panel shows that this sensor has a low ba ery, the

backup ba ery may need to be replaced.

Use a ﬂ at headed screw driver or other tool to slide the ba ery tray out of the

device. Remove the ba ery from the tray and replace with a new CR2032A

ba ery. Slide the ba ery tray back into the unit, making sure that the tray is fully

inserted into the unit.

✓ NOTE: Use Panasonic CR2032A ba eries or equivalent. Use of another ba ery

may damage or nega vely aﬀ ect the opera on of the device.

End-of-Life

The Smoke Detector Sensor does not have an End-of-Life (EOL), however the

smoke detector(s) that this device monitors may have an EOL condi on. Follow

the owner's manual for the smoke detector regarding instruc ons on proper

smoke detector EOL condi ons.

SMOKE DETECTOR