Galaxie Galaxie PV-440 Benutzerhandbuch - Seite 3
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Rasen- und Gartengeräte Galaxie Galaxie PV-440 herunter. Galaxie Galaxie PV-440 4 Seiten. Flowtron mosquito powervac owner's manual
Seite drucken5. Install MA-1000 Octenol Attractant Cartridge:
U.S. Government and university researchers have demon-
strated that o c t e n o l, a component of human respiration, is
an attractant to mosquitoes and biting fli e s .
The Galaxie PowerVac uses a specially designed time
release cartridge containing octenol (1-OCTEN-3-OL).
Install the Octenol Cartridge as follows:
a . Release the hood latch by pulling top of latch forward.
b . Raise the hood up to a vertical position.
c . Remove the octenol cartridge
from its package and peel off
the adhesive label covering the
evaporation holes.
d. Place the cartridge in the rec-
tangle well in the center of the
plenum with the evaporation
holes facing upward.
See Illustration 4.
e. Close hood and secure the
hood latch.
6 . Position and screw power pack to either an outside or
inside wall adjacent to a 115/120 volt A.C. outlet (screws
not provided). Run the low voltage wire either above or
below ground from the power pack to the unit. Plug the
low voltage wire into the power cord connector located at
the bottom of the PowerVac. Plug the power pack into the
electrical outlet.
7 . Place the switch located at the rear on the underside of
the unit adjacent to the power cord to the "on"position.
Note: Hood must be down and latched to ensure
that the built-in interlock is engaged and will allow
power to come on.
When the power is applied, the ultraviolet blacklight-blue
bulb will emit a bluish glow, the axial fan will rotate, the
four colored LED's will light and oscillate and the built-in
heater will heat the entry louver to body temperature.
Maintenance
1. Collection Tray:
Empty the collection tray periodically to ensure proper air
flow through the trap. To remove the collection tray, push
in on the latch at the front of the tray and pull tray down.
2. Octenol Cartridge:
Replace the octenol cartridge after approximately three
weeks of Galaxie PowerVac usage.
3. Ultraviolet Blacklight-Blue Bulb:
To replace the blacklight-blue bulb:
NOTE U l t r aviolet or " bl a ck l i g h t " is inv i s i ble to the
eye, and its ability to attract insects diminishes ov e r
t i m e. T h e r e fo r e, although the bulb appears to be
functioning it should be replaced ev e ry season to
maintain optimal " bl a ck l i g h t " e f fe c t i v e n e s s .
a. Place on/off switch to the "off" position and disconnect
power cord.
b. Open hood latch and raise hood to an upright position.
illustration 4
Cl e a n i n g
B r u s h
O c t e n o l
P l e n u m
Page 3
c. Pull bulb out of its socket.
d. Insert replacement bulb.
e. Close hood and secure with latch
f. Connect power cord and return switch to the "on" position.
Use only Flowtron BF-200 replacement bulbs available
from your dealer or from www.flowtron.com.
4. Axel Fan and Funnel:
Clean the axel fan and funnel each time the octenol car-
tridge is replaced or more often during periods of heavy
insect infestation.
CAUTION
A lw ays disconnect the power cord from its electrical
s o u rce before serv i c i n g , handling or cleaning the unit.
To clean the Fan and Funnel, open the hood latch and lift
the hood to an upright position.
a. Clean fan blades and area between the fan blades and
the surrounding fan housing using the cleaning brush
provided. The brush is located behind the Octenol well.
Simply slide the brush out from its stored location.
When complete place cleaning brush back in its proper
storage location.
See illustration 4.
b. To clean the funnel, remove the collection tray and then
Push rear of bottom funnel
ring up into the unit's housing
until front tabs become
disengaged from housing.
See figure A .
Pull funnel down and forward
releasing rear section of upper
funnel surface and remove
funnel from unit. See fig u r e B .
Remove insect debris from
screen surrounding funnel.
Wash screen with water and
shake off excess water before
r e - i n s t a l l i n g .
Re-install funnel by holding
funnel at a slight angle and
inserting the front edge of the
upper funnel surface inside of
u n i t 's housing. See figure C.
Push funnel upwards and with
the rear section of the bottom
funnel ring at a slight angle
compress funnel until front
tabs of bottom funnel ring are
up inside of the housing.
See figure D.
Close hood, secure with latch, connect power cord and
return the on/off switch to the "on" position.
Figure A
Up
Housing
Front
Bottom
Tab
Funnel
Ring
Push Up Here
Figure B
Down
Forward
Upper
Funnel
Tabs
Surface
Figure C
Front
Up
Edge
of Upper
Funnel Surface
Figure D
Up