Autonics T4MI Produkthandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Produkthandbuch für Temperaturregler Autonics T4MI herunter. Autonics T4MI 3 Seiten. 1-channel digital temperature indicators

Seite drucken
• Do not use the unit for other purpose (e.g. voltmeter, ammeter), but temperature
controller.
• 12-24 VDCᜡ power supply should be insulated and limited voltage/current or Class 2,
SELV power supply device.
• Make a required space around the unit for radiation of heat. For accurate temperature
measurement, warm up the unit over 20 min after turning on the power.
• Install a surge absorber at each end of inductive load coil when controlling high-capacity
power relay or inductive load (e.g. magnet).
• Make sure that power supply voltage reaches to the rated voltage within 2 sec after
supplying power.
• Do not wire to terminals which are not used.
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in 'Specifications')
- Altitude Max. 2,000 m
- Pollution degree 2
- Installation category II
Ordering Information
This is only for reference, the actual product does not support all combinations.
For selecting the specified model, follow the Autonics website .
T
❶
❷
I
-
❶ Digit
3: 3 digit
4: 4 digit
❷ Size
N: DIN W 48 × H 24 mm
Y: DIN W 72 × H 36 mm
W: DIN W 96 × H 48 mm
S: DIN W 48 × H 48 mm (8 pin plug type)
M: DIN W 72 × H 72 mm
H: DIN W 48 × H 96 mm
L: DIN W 96 × H 96 mm
❹ Input type and using range
PN Input
Using range
0 to 200 ℃
K2
K4
0 to 400 ℃
K(CA)
K8
0 to 800 ℃
KA
Thermo
0 to 999 ℃
-couple
KC
0 to 1200 ℃
J2
0 to 200 ℃
J4
J(IC)
0 to 400 ℃
J5
0 to 500 ℃
RF
R(PR)
600 to 1600 ℃
-99.9 to 99.9 ℃
P0
P0
-99.9 to 199.9 ℃ -
-99 to 199 ℃
P0
RTD
DPt100Ω
P1
0 to 99.9 ℃
P2
0 to 200 ℃
P4
0 to 400 ℃
• Contact us for temperature unit ℉ model.
Product Components
• Product (+ bracket)
[T4YI] Product, bracket × 2
Sold Separately
• 8 pin socket: PG-8, PS-8 (N)
• Terminal protection cover: RMA / RHA / RLA Cover
Initial Display When Power is ON
When power is supplied, all display parts turn ON for 1 sec. After displaying model type,
it returns to RUN mode.
2. Digit, alarm/
1. All display
option output
***8
T3NI
Errors
Display Description
Flashes when input sensor is disconnected or
sensor is not connected.
OPEN
HHHH Flashes when PV is higher than input range.
LLLL Flashes when PV is lower than input range.
N
❸
N
❹
C
-
❸ Power supply
X: 12-24 VDCᜡ
4: 100-240 VACᜠ 50/60 Hz
T4YI
T3NI
T3SI
T3HI
T4WI
○
-
-
-
○
-
-
-
○
○
-
-
○
○
-
-
-
○
-
-
○
-
-
-
○
○
○
-
○
○
-
-
-
-
-
-
○
-
-
-
○
-
-
-
○
-
-
○
○
-
-
○
-
-
-
○
○
○
○
• Instruction manual
3. Control output, input
4. RUN mode
and temperature range
NP4C
200
Troubleshooting
Check input sensor status.
When input is within the rated input
range, this display disappears.
Specifications
Series
Power supply
Power consumption
Input specification
Display accuracy
01)
Display type
Dielectric strength
Vibration
Insulation resistance
Noise immunity
Ambient temperature
Ambient humidity
Accessory
Approval
N
Unit weight (packaged)
01) In case of T3NI, T3SI Series and the decimal point display models
At room temperature (23 ℃ ±5 ℃): (PV ±0.5% or ±2 ℃ higher one) ±1 digit
Out of room temperature range: (PV ±0.5% or ±3 ℃ higher one) ±1 digit
Dimensions
• Unit: mm, For the detailed drawings, follow the Autonics website.
• Below is based on T3SI Series.
A
T4MI
T4LI
-
-
○
-
○
Body
-
A
B
○
T3NI
48
24
-
T4YI
72
36
○
T4WI
96
48
-
○
T3SI
48
48
-
T3HI
48
96
-
T4MI
72
72
-
T4LI
96
96
○
■ Bracket
T3NI
42
45.2
48.6
T4WI
20
53.5
T3HI/T4MI/T4LI
46
12
23.9
T3, T4 Series
100 - 240 VACᜠ 50/60 Hz ±10% (T3NI: 12 -24 VDCᜡ ±10%)
≤ 5 VA (T3NI: ≤ 1 W)
Refer to 'Ordering Information: Input type and using range'.
• At room temperature (23 ℃ ±5 ℃):
(PV ±0.5% or ±1℃ higher one) ±1 digit
• Out of room temperature range:
(PV ±0.5% or ±2 ℃ higher one) ±1 digit
7 Segment (red), LED type
Between input terminal and power terminal: 2,000 VACᜠ 50/60 Hz
for 1 min
0.75 mm amplitude at frequency of 10 to 55 Hz (for 1 min) in each X,
Y, Z direction for 2 hours
≥ 100 MΩ (500 VDCᜡ megger)
±2 kV square shaped noise (pulse width 1 ㎲) by noise simulator
R-phase, S-phase
-10 to 50 ℃, storage: -20 to 60 ℃ (no freezing or condensation)
35 to 85%RH, storage: 35 to 85%RH (no freezing or condensation)
Bracket
ᜫ
• T3NI: ≈ 25 g (≈ 48 g)
• T4YI: ≈ 123 g (≈ 181 g)
• T4WI: ≈ 140 g (≈ 231 g)
• T3SI: ≈ 80 g (≈ 120 g)
• T3HI: ≈ 137 g (≈ 203 g)
• T4MI: ≈ 137 g (≈ 202 g)
• T4LI: ≈ 185 g (≈ 274 g)
D
E
C
Panel cut-out
C
D
E
F
G
4
-
48
21
≥ 55
7
-
93
30
≥ 91
12
-
100
45
≥ 116 ≥ 52
10.5
12.3
77.8
□45
≥ 65
13
-
70
91.5
≥ 65
11.8
14.3
75
□67.5 ≥ 90
12.5
-
70
□91.5 ≥ 115 ≥ 115 92
T4YI
32.4
26.4
10
T3SI
□49.5
60.3
■ Panel cut-out
G
I
H
I
J
≥ 37
45
22.2
+ 0.5
+ 0.3
0
0
≥ 40
68
31.5
+ 0.7
+ 0.6
0
0
92
45
+ 0.8
+ 0.6
0
0
≥ 65
45
45
+ 0.5
+ 0.5
0
0
≥ 115 45
92
+ 0.6
+ 0.8
0
0
≥ 90
68
68
+ 0.7
+ 0.7
0
0
92
+ 0.8
+ 0.8
0
0
73
30
30.5