ADENDORFF MAC AFRIC SDRILC-005 Original Betriebsanleitung - Seite 4
Blättern Sie online oder laden Sie pdf Original Betriebsanleitung für Kraftschraubendreher ADENDORFF MAC AFRIC SDRILC-005 herunter. ADENDORFF MAC AFRIC SDRILC-005 14 Seiten. Cordless brushless driver/hammer drill
Seite drucken
ADDITIONAL SAFETY RULES
1. To be safe, disabled, retarded, untrained people or people disable to operate
independently, including young children, are discouraged to operate the tool without
supervision. Young children should be supervised to ensure that they do not play with
the tool.
2. Check the tool and battery carefully before putting it into use. Stop operation
immediately when malfunctions be found and send the tool to be repaired by qualified
serviceman. Do not open the tool yourself.
3. Use only original MAC AFRIC SBATTR-002/004 type rechargeable Li-Ion battery for this
tool and recharge only with the MAC AFRIC SBATTR-002/004 type charger supplied with
the tool. Use of other type of battery or charger, e.g. imitated, modified or with other
brand, may result in a risk of battery burst causing personal injury and property damage.
4. Hold tool by insulated gripping surfaces when performing an operation on wall and floor
where the cutting tool may contact hidden wiring. Contact with a "live" wire will also
make exposed metal parts of the tool "live" and shock the operator.
5. Use appropriate detectors to determine or consult local power supply units for relative
data if utility lines, such as electric lines, gas lines and water lines are hidden in the
work area before screwing or drilling on the wall, floor or ceiling. Once those utility lines
are drilled, it will cause fire and electric shock accidents, explosion or other damages to
properties.
6. Switch off the tool immediately once the drill insert jams. Be prepared for high reaction
torque that can cause kick-back. Free the tool by reversing its rotation. The tool insert
jams when the tool is subject to overload or it becomes wedged in the workpiece.
7. Always be sure to hold the tool firmly. High reaction torque can briefly occur while
driving in and loosening screws.
8. Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held
more secure than by hand.
9. Keep working area clean. Blends of materials are particularly dangerous. Dust from light
alloys can burn or explode.
10. Always wait until the tool has come to a complete stop before placing it down. The drill
-5-
bit insert can jam and lead to loss of control over the tool.
11. Keep hands away from rotating parts.
12. Always be sure to have a firm footing and be sure no one is below when using the tool in
high locations.
13. Do not touch the drill bit or the workpiece immediately after operation; they may be
extremely hot and could burn your skin.
14. Always wear protective devices to avoid personal injury.
15. Damaged tools, accessories and deposed packages should be recycled in an
environmentally friendly way in accordance with the local law.
16. Wear ear protector when operating impact drill or it may cause hearing damage.
17. Always use the auxiliary handle if offered with the tool. Out of control over the tool may
cause injury.
SAVE THESE INSTRUCTIONS.
WARNING! MISUSE or failure to follow the safety rules stated in this instruction manual may
cause serious personal injury.
IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY AND
CHARGER
1. Always set the reversing switch lever in the central position (lock the switch) and remove
the battery cartridge before tool change, inspection, maintenance, transportation,
storage or something like that.
2. Always check and confirm the battery cartridge is installed properly before use.
3. It's normal that the battery will become a little bit hotter while charging.
4. Do not charge for the damaged battery.
5. After charging, unplug the charger from power source and then remove the battery
cartridge from the charger. Do not leave the battery cartridge in the charger after the
charging cycle is completed.
6. Do not put the charged battery cartridge in the charger when the tool is not used.
7. Do not disassemble charger or battery; take it to a qualified serviceman when service or
-6-
-7-