Hifonics Zeus ZXi6406 Handbuch - Seite 10
Blättern Sie online oder laden Sie pdf Handbuch für Auto-Verstärker Hifonics Zeus ZXi6406 herunter. Hifonics Zeus ZXi6406 15 Seiten.
Seite drucken
- 1. Table of Contents
- 2. General Installation Procedure
- 3. Amplifier Feature Descriptions
- 4. Zxi6006 / Zxi1006 2 CHANNEL AMPLIFIER APPLICATIONS
- 5. Zxi4406 / Zxi6406 4 CHANNEL AMPLIFIER APPLICATIONS
- 6. Zxi8006 5 CHANNEL AMPLIFIER APPLICATIONS
- 6. Channel Discrete, One Being Mono Low Pass / 3 or 4 Channel Discrete, One Being Mono Low Pass / 3 Way Active
- 6. Front/Rear High Pass, with Constant Sub Bass
- 7. Setting up Systems after Installation for Best Performance
- 8. Troubleshooting and Diagnostics
- 9. Features and Specifications
- 10. Product Warranty
ZXi8006 5 CHANNEL AMPLIFIER APPLICATIONS
3 way active, with mono bass
The ZXi8006 5 channel amplifier contains all the functions necessary to set up a
The ZXi8006 5 channel amplifier contains all the functions necessary to set up a
completely self contained 3 way active crossover system.
completely self contained 3 way active crossover system.
Interconnect cable checklist:
Interconnect cable checklist:
Use good quality RCA cables to connect the inputs of channels 1&2 to the full
Use good quality RCA cables to connect the inputs of channels 1&2 to the full
range outputs of the source.
range outputs of the source.
Switch setting checklist:
Switch setting checklist:
- INPUT MODE: CH2
- INPUT MODE: CH2
- CH 1 / 2 X-OVER: HP
- CH 1 / 2 X-OVER: HP
- CH 3 / 4 X-OVER: BP
- CH 3 / 4 X-OVER: BP
Crossover frequency control checklist:
Crossover frequency control checklist:
- CH 1 / 2 HIGH PASS: 1KHz to 4KHz
- CH 1 / 2 HIGH PASS: 1KHz to 4KHz
- CH 3 / 4 HIGH PASS: 100 Hz
- CH 3 / 4 HIGH PASS: 100 Hz
- CH 3 / 4 LOW PASS: 1KHz to 4KHz
- CH 3 / 4 LOW PASS: 1KHz to 4KHz
- CH 5 LOW PASS: 100 Hz
- CH 5 LOW PASS: 100 Hz
CH 1&2
FULL RANGE
INPUTS
Front/rear high pass, with constant sub bass
Another obvious application for the ZXi8006 is to use 4 channels for front/rear
Another obvious application for the ZXi8006 is to use 4 channels for front/rear
satellites, and the mono channel for constant non faded sub bass.
satellites, and the mono channel for constant non faded sub bass.
Interconnect cable checklist:
Interconnect cable checklist:
Use good quality RCA cables to connect channels 1,2,3&4 inputs to the front
Use good quality RCA cables to connect channels 1,2,3&4 inputs to the front
and rear outputs of the source as shown.
and rear outputs of the source as shown.
Switch setting checklist:
Switch setting checklist:
INPUT MODE: 4CH
INPUT MODE: 4CH
- CH 1 / 2 X-OVER: HP
- CH 1 / 2 X-OVER: HP
- CH 3 / 4 X-OVER: HP
- CH 3 / 4 X-OVER: HP
Crossover frequency control checklist:
Crossover frequency control checklist:
- CH 1 / 2 HIGH PASS: 100 Hz
- CH 1 / 2 HIGH PASS: 100 Hz
- CH 3 / 4 HIGH PASS: 100 Hz
- CH 3 / 4 HIGH PASS: 100 Hz
- CH 3 / 4 LOW PASS: N/A
- CH 3 / 4 LOW PASS: N/A
- CH 5 LOW PASS: 100 Hz
- CH 5 LOW PASS: 100 Hz
CH 1&2
FRONT
INPUTS
CH 3&4
REAR
INPUTS
8
Note that the HIGH and LOW PASS controls of channels 3&4 act as the
Note that the HIGH and LOW PASS controls of channels 3&4 act as the
bandpass controls.
bandpass controls.
Please note that these frequency points are suggestions only. Refer to the
Please note that these frequency points are suggestions only. Refer to the
loudspeaker manufacturer specifications and the section "Setting up systems
loudspeaker manufacturer specifications and the section
after installation for best performance"
after installation for best performance"
Level control checklist:
Level control checklist:
- Refer to the section "Setting up systems after installation for best performance"
- Refer to the section
"Setting up systems after installation for best performance"
Minimum final loudspeaker impedances:
Minimum final loudspeaker impedances:
- 2 ohm per channel
- 2 ohm per channel
Please note that these frequency points are suggestions only. Refer to the
Please note that these frequency points are suggestions only. Refer to the
loudspeaker manufacturer specifications and the section "Setting up systems
loudspeaker manufacturer specifications and the section
after installation for best performance"
after installation for best performance"
Level control checklist:
Level control checklist:
- Refer to the section
- Refer to the section "Setting up systems after installation for best performance"
"Setting up systems after installation for best performance"
Minimum final loudspeaker impedances:
Minimum final loudspeaker impedances:
- 2 ohm per channel
- 2 ohm per channel
"Setting up systems
CH 5 MONO
SUBWOOFER
CH 3&4
REAR HIGHS
SPEAKERS
CH 1&2
TWEETERS
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND
"Setting up systems
CH 5 MONO
SUBWOOFER
CH 3&4
REAR HIGHS
SPEAKERS
CH 1&2
FRONT HIGHS
SPEAKERS
TO BATTERY +12v
VIA FUSE
REMOTE TURN-ON
CHASSIS GROUND