DC SG50 IS D Betriebs- und Wartungsanleitung

Blättern Sie online oder laden Sie pdf Betriebs- und Wartungsanleitung für Geschirrspüler DC SG50 IS D herunter. DC SG50 IS D 2 Seiten.

Seite drucken

DC SG50 IS D Betriebs- und Wartungsanleitung

POWER

LAMP

(OPTIONAL DRAIN PUMP)

REMOVE DRAIN PLUG THEN

SWITCH THE MACHINE OFF

TO START THE AUTOMATIC

DRAIN PUMP CYCLE

POWER

SWITCH

PREPARATION

 CHECK THE DRAIN PLUG IS PUSHED FIRMLY IN PLACE AND FILTERS ARE PROPERLY SECURED.

 CHECK THE DETERGENT CHEMICAL ( RED ) AND RINSE AID CHEMICAL ( CLEAR ) SUPPLY TUBES - WITH FOOT VALVES - ARE SUBMERGED IN SUFFICIENT PRODUCT.

 CHECK THE DOOR IS CLOSED AND PRESS THE POWER SWITCH - THE GREEN POWER LAMP WILL COME ON.

 ALLOW 30 MINUTES FOR THE MACHINE TO FILL WITH WATER AND REACH THE CORRECT WASHING TEMPERATURE.THE MACHINE READY LAMP WILL COME ON.

OPERATION

 REMOVE ALL DEBRIS FROM THE GLASSES TO BE WASHED BEFORE PLACING THEM INTO THE BASKET.

 CLOSE THE DOOR - PRESS THE CYCLE START SWITCH - THE CYCLE LAMP WILL COME ON.

 AT THE END OF THE CYCLE THE WASH CYCLE LAMP WILL GO OUT - OPEN THE DOOR AND PULL OUT THE BASKET.

 ALLOW EXCESS WATER TO RUN OFF BEFORE REMOVING.

ROUTINE MAINTENANCE

 AT THE END OF A SESSION TURN OFF THE POWER SWITCH. DO NOT REMOVE THE FILTER AT THIS STAGE.

 REMOVE THE DRAIN PLUG - THE WASH TANK WILL EMPTY - (MACHINES FITTED WITH DRAIN PUMP WILL AUTOMATICALLY START TO PUMP THE WATER OUT).

 COLLECT THE DEBRIS AND REMOVE FROM THE WASH TANK.

 CLEAN AROUND THE WASH TANK - DOOR SURROUNDS AND HINGES WITH AN 'ADDIS'' TYPE WASHING UP BRUSH AND CLEANING CLOTH.

 DO NOT USE CHLORIDE OR BLEACH CONTAINING BASED CLEANING SOLUTIONS OR ABRASIVES WHEN CLEANING THE WASH TANK.

 TAKE OUT THE MAIN FILTER - CLEAN THOROUGHLY AND REPLACE .

 DO NOT ALLOW DEBRIS TO GO DOWN THROUGH THE FIXED FILTER AND OUTLET HOLE AS THIS MAY DAMAGE YOUR MACHINE.

 REGULARLY CHECK RINSE JETS AND WASH JETS ARE CLEAR OF DEBRIS OR LIME SCALE - REMOVE IF NECESSARY BY UNSCREWING THE RINSE ARM NUT THAT HOLDS THE

RINSE ARM IN PLACE - REMOVE THE RINSE PIN THAT HOLDS THE WASH ARM IN PLACE - CLEAN BOTH THOROUGHLY AND REASSEMBLE.

WATER SOFTENER REGENERATION

 THE SALT LOW LAMP WHEN ON WARNS IF THE SALT CONTAINER IS EMPTY.

 UNSCREW THE SALT CONTAINER LID LOCATED INSIDE THE WASH TANK AND FILL WITH GRANULAR CATERING SALT ( THE FULL CONTAINER WILL

APPROXIMATELY REGENERATE FOUR REGENERATION CYCLES & HOLDS 1 Kg OF SALT).ENSURE THE SALT CONTAINER LID IS SECURE AFTER FILLING.

 REMOVE THE DRAIN PLUG FROM THE MACHINE DURING THE REGENERATION OF THE WATER SOFTENER.

 THE MACHINE POWER SWITCH MUST BE OFF TO ENABLE THE REGENERATION CYCLE.

 CLOSE THE DOOR AND PRESS THE REGENERATION SWITCH. THE WATER SOFTENER REGENERATION LAMP WILL COME ON.

 THE REGENERATION OF THE WATER SOFTENER WILL TAKE AROUND 20 MINUETS AND WILL BE FULLY AUTOMATIC.

 THE WATER SOFTENER REGENERATION LAMP WILL GO OUT AND THE MACHINE WILL SWITCH OFF AUTOMATICALLY AFTER THE REGENERATION

CYCLE IS COMPLETE. REMEMBER TO REPLACE THE DRAIN PLUG BEFORE RE-FILLING THE MACHINE.

 MEDIUM-WATER HARDNESS MAY REQUIRE FOUR REGENERATIONS A WEEK. MEDIUM TO HARD-WATER HARDNESS MAY REQUIRE DAILY REGENERATION.

RINSE ARM

RINSE

JETS

WASH ARM

SERVICE CALLS TO RECTIFY FAULTS CAUSED BY `THE LACK OF ROUTINE MAINTENANCE` WILL BE CHARGED FOR

OPERATING AND MAINTENANCE INSTRUCTIONS

SG35 IS D / SG40 IS D / SG45 IS D / SG50 IS D

WASH CYCLE

LAMP

CYCLE START

SWITCH

RINSE ARM NUT

RINSE PIN

WASH JETS

AND YOUR WARRANTY MAY BE AFFECTED

www.directcatering.co.uk

REGENERATION

(REMOVE DRAIN PLUG DURING THE REGENERATION)

FOOT VALVES FOR

SALT CONTAINER

CHEMICAL

CONTAINER TUBES

SALT LOW

MACHINE READY

LAMP

WATER SOFTENER

START SWITCH

LID

DRAIN PLUG

MAIN FILTER

FIXED FILTER

OUTLET HOLE