Autonics CR Series Produkthandbuch - Seite 3

Blättern Sie online oder laden Sie pdf Produkthandbuch für Sicherheitssensoren Autonics CR Series herunter. Autonics CR Series 3 Seiten. Cylindrical capacitive proximity sensors

Seite drucken
Cut-out Dimensions
• Unit: mm, For the detailed drawings, follow the Autonics web site.
H
TAP
Ø A
B
Mutual-interference & Influence by Surrounding Metals
■ Mutual-interference
When plural proximity sensors are mounted in a close row, malfunction of sensor may
be caused due to mutual interference.
Therefore, be sure to provide a minimum distance between the two sensors, as below
table.
[Face to Face]
A
■ Influence by surrounding metals
When sensors are mounted on metallic panel, it must be prevented sensors from
being affected by any metallic object except target. Therefore, be sure to provide a
minimum distance as below chart.
ℓ
Sensing side
Ø 18 mm
Item
A
48
B
54
ℓ
20
54
Ø d
m
24
n
54
Tightening Torque
Use the provided washer to tighten the nuts.
The tightening torque of the nut varies with the distance from the fore-end. [Figure 1]
If the nut tip is located at the front of the product, apply the front tightening torque.
the allowable tightening torque table is for inserting the washer as [Figure 2].
[Figure 1]
Nut tip
Fore-end
Front
Rear
Sensing side
Ø 18 mm
Strength
Front size
-
Front torque
0.39 N m
Rear torque
0.39 N m
Ø 18 mm Ø 30 mm
Mounting
Ø 18.5
Ø 30.5
+0.5
+0.5
hole (H)
0
0
TAP
M18×1
M30×1.5
Ø 18 mm Ø 30 mm
Ø A
26.5
42
B
24
35
[Parallel]
B
m
Ø d
n
ℓ
ℓ
(unit: mm)
Ø 30 mm
90
90
10
90
45
90
[Figure 2]
Mounting side
Washer
Ø 30 mm
12 mm
49 N m
78.4 N m
Sold Separately: M12 Connector Cable
• For detailed information, refer to the 'M8/M12 Connector Cable' manual.
Appearance
Power
Connector 1 Connector 2 Length
M12 (Socket-
AC
Female)
4-pin
M12 (Socket-
AC
Female)
4-pin
M12 (Socket-
AC
Female)
4-pin, L type
M12 (Socket-
AC
Female)
4-pin, L type
Sold Separately: Protection Cover (P90-M□)
The welding tip (spatter) generated during arc welding has a property of sticking to
plastics and metals. If several welding tips are attached to the front or body of the
proximity sensor, it may be difficult to replace the body or cause a malfunction.
When using a general type proximity sensor, use a silicone protective cover (sold
separately). Only for flush (shield) type.
Model
P90-M12
Item (mm)
A
Ø 11
B
Ø 14
C
5.0
D
1.0
Applied sensing side size
M12
Sold Separately: Fixing Bracket (P90-R□)
If fixing holes are not made for cylindrical proximity sensor, use a cylindrical fixing
bracket as below. For Non-flush (non-shield) type, be sure effect by ambient material.
Side view
Front view
Model
P90-R12
Item (mm)
A
24 ± 0.2
B
≤ 11.5
C
20
D
Ø 12
E
≤ 34.4
F
6.0
Fixing bolt
M4 × 20
Applied sensing side size
M12
18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002
www.autonics.com | +82-2-2048-1577 | [email protected]
Feature
Model
2 m
CIA2-2
2-wire
PVC
5 m
CIA2-5
2 m
CIAH2-2
Oil resistant
2-wire
PVC
5 m
CIAH2-5
2 m
CLA2-2
2-wire
3 m
PVC
CLA2-3
5 m
CLA2-5
2 m
CLAH2-2
Oil resistant
2-wire
PVC
5 m
CLAH2-5
Ø 1
D C
P90-M18
P90-M30
Ø 17
Ø 28.5
Ø 21
Ø 33
6.0
8.0
3.0
6.0
M18
M30
A
E
P90-R18
P90-R30
32 ± 0.2
45 ± 0.2
≤ 16
≤ 16
30
50
Ø 18
Ø 30
≤ 47
≤ 60
10
10
M5 × 30
M5 × 50
M18
M30