DynaSample XO-mini Schnellstart - Seite 2

Blättern Sie online oder laden Sie pdf Schnellstart für Probenehmer DynaSample XO-mini herunter. DynaSample XO-mini 5 Seiten.

Seite drucken

MIDI Connections

- Connect the USB-MIDI Out of your MIDI controller to any free USB port of your XO-mini.

- The USB-MIDI controller needs to support standard class compliant USB MIDI drivers in order to be

recognized. A USB hub usually works but not always (depending on the hardware) . . .

- For DIN-MIDI please use a class compliant USB-MIDI interface.

- Set your controller to transmit on MIDI channel 1.

☺

hint:

For testing the MIDI communication you can activate the MIDI Monitor when you have any kind of display connected.

Click [MIDI-MONITOR] on the HDMI screen to do so. Clicking again will bring you back to playing mode.

The MIDI KEY-REMOTE as well as a USB number pad (see below) allow you to navigate there as well.

It's in [Utility] and a few times to the left or on the number pad with the shortcut digits 1+3 at the same time.

General Operation Instructions (with HDMI-Monitor) -

On the XO-mini you can find 8 function keys underneath the display as well as left/right navigation buttons

(with [OK] and [Escape]) on the left and an incremental wheel with [+] / [-] buttons on the right hand.

With left / right [◄] / [►] you can navigate through the menus. The wheel or [+] / [-] and will change values.

In some cases (like MIDI program changes on the main page) this needs to be confirmed by pressing [OK].

[Escape] always cancels the current operation and takes you back to the main screen for patch selection.

By pressing it for at least 2 seconds a RESET is executed. This will also turn off stuck MIDI notes.

You can also simply use the "reset" button for executing a reset.

The right wheel selects the presets for the current Edit (MIDI) channel (ECn, displayed on the bottom right). In

other modes it is used for changing values. Click & hold, then drag up/down or left/right and release.

The 8 buttons underneath the display also serve as patch favorite buttons. (5-8 are only favorite buttons.)

Click briefly to recall - click and hold for 1-2 seconds to store your current patch (including bank number).

Setup of your MIDI / USB - Controllers

- Move to the left to [Utility] and press [OK] to enter [Utility].

Move several times to the right until "Internal Backup - All Settings & Maps" is shown.

Go to the 2

All optimized settings for your instrument will be automatically set up now.

Always return to the main screen with [Escape].

In case that you change the global settings later you can store your personal settings here by backing them up to one of

the user backup slots 1-5. This is done by navigating to the left parameter (e.g. "backup1" or "backup2" etc. followed by

pressing [OK].

Done (!):

Now you can select the different patches by sending MIDI program changes, using the key-remote or a USB number pad,

preset memory (favorites) buttons or the right wheel / [+] [-] buttons of the HDMI screen and play them.

Clicking onto the bank numbers or patch names opens drop down lists for easier and faster selection.

Listen to demos by moving to the left twice and press [OK]. [OK] or [Escape] will stop and return to normal playing mode.

Change your MASTER Volume, Transposition, Edit Channel or open the MIDI-Monitor by clicking onto the

corresponding buttons to the right of the blue display or use the shortcuts on a USB number pad.

For further information please refer to the owner's manual.

IMPORTANT (!):

Do NOT send any MIDI data during startup or will end up with crackling and a sluggish MIDI response!

Make sure to have your wind controller calibrated to use the full dynamic range without having to force it!

Check your dynamics / velocity on display line2. ||||||||* indicates that you are reaching the full dynamic range.

If your dynamics are too low you will feel unnecessary additional latency and slow attacks.

The settings of the EWI-USB will be overwritten during start-up. Please save your "previous" settings first.

If you are using an EWI5000 / Solo make sure to disable High Resolution for breath and follow this setup guide:

https://dynasample.com/downloads/EWI5000_setup_for_use_with_the_XPression.pdf

Known issues:

- The XO-mini "Edit Channel" and the controller need to be both MIDI channel 1 to match - display bottom right "EC1".

- A few sliders in the graphical editor are still not graphically updated atm even though they actually change values.

Have lots of fun with your new XO-mini!

DynaSample

parameter (right hand) and select your controller with the right wheel or [+] / [-]. Press [OK].

! ! ! ABSOLUTELY RECOMMENDED FOR 1

SETUP ! ! !