Autopage C3-RS-601 Schnellstart-Installationshandbuch

Blättern Sie online oder laden Sie pdf Schnellstart-Installationshandbuch für Fernstart Autopage C3-RS-601 herunter. Autopage C3-RS-601 2 Seiten. Remote car starter
Auch für Autopage C3-RS-601: Installationshandbuch (19 seiten)

Seite drucken

QUICK START INSTALLATION GUIDE

Help Auto Page protect our environment !

If you are not proficient in the installation of this product or would

like a full version of the installation manual, Please visit our web

site @

www.autopageusa.com

FOR PROFESSIONAL INSTALLATION ONLY!

RX-300A

FUSE

Valet

Switch

FUSE

H1 6 Pin Wht.

ANT.

Valet

LED

C3-RS-601

H6 DL

H3 10 Pin White

H2 5 Pin

Green : (-) Lock

(+) Unlock

Door Locks

Blue : (-) Unlock

(+) Lock

White/Red : Tachometer Signal Input

White/Blue : Instant Start (-) Input

White/Black : Safety, Hood Pin Input (-)

Black/White : Neutral Safety Switch (-) Input

White : Ground When Running By-pass Control Output

White/Violet : Safety Shutdown Brake Input (+)

H1 6 PIN HEAVY GAUGE WIRE HARNESS

20A

Red: Remote Start Power 1

20A

Red: Remote Start Power 2

Violet: Starter (+) Output

Pink: Ignition 2 (+) Output

Yellow: Ignition 1 (+) Output

Brown: Acc/Heater (+) Output

H5 5 PIN WIRE HARNESS

Red/White: Parking Light Relay Power Input

Violet : Starter Output

White: Parking Light Relay Output

Red : 12 Volt Input

Black: System Main Ground (-)

Red : 12 Volt Input

Yellow. Ignition 1 Output

Brown: Siren (+) Output

Pink : Ignition 2 Output

Red: 12v + Battery Power

Brown ACC Output

PROGRAMMING TRANSMITTER

LED Indicator

Note: This model will only retain the last 4 remote transmitters programmed. If the

transmitter memory is exceeded, the security system will start deleting transmitters from

memory in chronological order.

1. Turn the Ignition 'switch „OFF/ON‟ 3 TIMES and stay in ON position.

"Within 15 seconds".

2. Push the Valet switch 2 times and hold it on the 2

then release the valet switch. You are now in the Transmitter programming mode.

3. Press and hold any button of the transmitter until the siren responds with a confirming

chirp, indicating the signal has been stored into memory.

4. If you have additional transmitters (up to 4) that need to be programmed, repeat step 3

for remaining transmitters.

FEATURE PROGRAMM

FEATURE "I" PROGRAMMING:

1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.

2. Push the Valet switch 1 times (holding in on the 1

long chirp is heard, then release the valet switch. You are now in the Alarm feature

"A" programming mode.

3. Press and release the transmitter button corresponding to the feature you want to

program.

One Chirp /

Press

LED one pulse

Red/White : Parking light Input

Transmitter

Factory Default

Button

White : Parking light Output

Setting

Black : System Ground

H3/2 White/Blue

Brown : Programmable Output (-)

= 1 Pulse

Horn (-) or Factory Rearm (-)

Remote Start

FUSE

Red : System Power + 12 Volt

H3/8 Pink Wire =

Yellow : Ignition 3 Output ( 200 mA - )

Factory Security

Disarm Signal

Blue/Black : ACC 2 ( 200 mA - )

Output

Pink : 200mA Programmable Output (-)

H2/4 Brown Wire

= Horn Output

Gray : CH 3 Trunk Release (-)

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking

light flashes will confirm exit.

FEATURE "II" PROGRAMMING:

1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.

2. Push the Valet switch 2 times (holding in on the 2

long chirp is heard, then release the valet switch. You are now in the Alarm feature

"A" programming mode.

3. Press and release the transmitter button corresponding to the feature you want to

program.

One Chirp /

Press

LED one pulse

Transmitter

Factory Default

Button

Setting

Button Two

Push Remote

Without ignition

controlled door

locks & unlocks

Gasoline Engine

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking

light flashes will confirm exit.

FEATURE "III" PROGRAMMING:

1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.

2. Push the Valet switch 3 times (holding in on the 3

chirp is heard, then release the valet switch. You are now in the Alarm feature "A"

programming mode.

3. Press and release the transmitter button corresponding to the feature you want to

program.

Press

Transmitter

Button

push until a long chirp is heard

Exit: Turn Ignition to 'OFF' position, or leave it for 15 seconds. 3 long chirps & 3 parking

light flashes will confirm exit.

FEATURE "IV" PROGRAMMING:

push) until one chirp with one

1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.

2. Push the Valet switch 4 times (holding in on the 4

chirp is heard, then release the valet switch. You are now in the Alarm feature "A"

programming mode.

3. Press and release the transmitter button corresponding to the feature you want to

program.

Two Chirps /

Three Chirps/

LED two pulse

LED three pulse

Press

Transmitter

Button

H3/2 White/Blue = 3

Pulse Remote Start

H3/8 Pink Wire =

H3/8 Pink Wire = 20

Start Status (Shock

Second Ground out

Sensor Bypass

Key Sensor By-pass

Control) Output

H2/4 Brown Wire =

Rearm Signal Output

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will

confirm exit.

FEATURE "V" PROGRAMMING:

1. Turn the Ignition 'switch „ON/OFF‟ 3 TIMES and stay in OFF position.

2. Push the Valet switch 5 times (holding in on the 5

push) until one chirp with one

chirp is heard, then release the valet switch. You are now in the Alarm feature "A"

programming mode.

3. Press and release the transmitter button corresponding to the feature you want to

program.

Press

Two Chirps /

Three Chirps /

Four Chirps /

Transmitter

LED two pulse

LED three pulse

LED four pulse

Button

One push

Remote Start

Ignition

controlled

door locks &

unlocks

Diesel Engine

Exit: Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps & 3 parking light flashes will

and 20

and 10 seconds

and 15 seconds

confirm exit.

seconds warn-

warn-up timer

up timer

C3-RS-601

push) until one chirp with one long

One Chirp /

LED one

Two Chirps /

Three Chirps /

Four Chirps /

pulse

LED two pulse

LED three pulse

LED four pulse

Factory

Default

Setting

20 minutes

10 minutes run

30 minutes run

5 minutes run

run time

time

0.8-second

3.5-second

0.8 second

0.8 second dbl

Door lock &

Door

lock, 0.35

lock,0.8 second

Unlock.

Lock & Unlock.

second unlock

dbl unlock

Five chirps= 0.8 second lock, dbl 0.8 second unlock

Six chirps= dbl 0.8 second lock, 0.8 second unlock

Door Lock

before & after

This Remote Starter with Alarm and Keyless Entry System

start * This is the

Door Lock

Door Lock after

preferred setting

Without this

has been designed to be installed on fuel-injected vehicles

before start

start

when using the

feature

with an automatic transmission ONLY.

optional XT-11

single button

remote

transmission vehicle.

safety switch so it will not start in any forward or reverse

gear.

vehicles with a purple starter wire have a mechanical-type

push) until one chirp with one long

park safety switch instead of electrical safety switch. The

mechanical type does not interrupt the starter circuit when

the transmission is in any gear and does not offer the 100%

level of safety required for remote starting purposes.

Therefore, our system should never be installed on any

One Chirp /

vehicle that uses a mechanical type park safety switch.

LED one

Two Chirps /

Four Chirps

pulse

Three Chirps /

LED two pulse

/ LED four

Factory

LED three pulse

pulse

vehicle will not start in any forward or reverse gear,

Default

Setting

regardless of the type of vehicle.

DBI TACH

Tachometer

Voltage checking

Timer checking

checking type.

type

DATA

or steering linkage.

ONLY !!

RPM learning

immobilizer system that can severely complicate the

0.8-second (2 chirps), 1.0-second (3 chirps), 1.2-second (4

Start Timer:

chirps), 1.4-second (5 chirps), 1.6-second (6 chirps), 1.8-

installation. There is a possibility that this system cannot be

0.6-second

second (7 chirps), 2.0-second (8 chirps), 3.0-second (9

installed on some immobilizer-equipped vehicles.

chirps), 4.0-second (10 chirps),

Low ceck

Hi check level

extreme care and do not probe any wires of the SRS

level

system.

vehicle.

that no wiring harness or other components are located

behind the panels that would otherwise be damaged.

push) until one chirp with one long

Poor wiring, i.e. taped joints will possibly introduce

unreliability into the alarm system and may result in false

alarms or incorrect operation. We suggest soldering all

One Chirp /

Four

connection points.

Two Chirps /

LED one pulse

Three Chirps /

Chirps /

LED two pulse

Factory

LED three pulse

LED four

prevent possible damage to wires.

Default Setting

pulse

Second

Second Start

Accessory

H3/9 Blue/Black

+ 50 RPM

No RPM learning

DBI ONLY

- 50 RPM

No RPM Learning or < 50RPM

DBI ONLY

FEATURE "V" MUST BE PROGRAMMED FOR THE

UNIT TO RESPOND TO REMOTE START!

If you are not sure or do not understand any part of

the quick start guide, please download the complete

installation

manual

available

www.autopageusa.com

This quick start guide is a

brief outline for professional installers that are

familiar with the installation and operation of this

remote start system.

Please test all of your

installation to insure proper operation of the vehicle

before returning it to the customer.

For authorized dealer technical support, please call

800-945-2527

and

wait

for

the

first

available

technician.

Technical support hours are Monday

through Saturday from 8:00 to 5:00 Pacific standard

time.

Never

install this

remote starter

a manual

This system must be installed and wired through a

Some automatic transmission vehicles mainly older GM

Once you install this system, you must verify that the

Read the operation manual for operating.

Do not install any component near the brake, gas pedal

Some vehicles have a factory installed transponder

Most vehicles have an SRS air bag system. Use

Disconnect the car battery before beginning work on the

Check behind panels before drilling any holes. Ensure

Do not use conventional crimp lock, bullet on any wiring.

Install the wiring neatly under carpets or behind trim to

960 Knox Street Unit B

Torrance, California 90502

Main Office: 310-323-1800

Technical Support: 800-945-2527

(For Authorized Dealers Only)