High Tech Pet Power Pet PX-1 Installations- und Betriebsanleitung - Seite 8
Blättern Sie online oder laden Sie pdf Installations- und Betriebsanleitung für Haustierpflegeprodukt High Tech Pet Power Pet PX-1 herunter. High Tech Pet Power Pet PX-1 13 Seiten. Fully automatic pet door
Seite drucken
4 WAY ACCESS CONTROL: Individual activation buttons for the inside and outside sensors give you a 4-way access
control system. You can allow your pet to come in but not go out, go out but not come in, come in and out or close and
lock the door altogether
AUTOMATIC CLOSE CONTROL: Your POWER PET PX Features a smart sensing circuit that keeps the door panel open
as long as it is receiving the signal from your pet's collar. Once your pet has moved completely through the opening, the
panel immediately closes. No need to adjust a manual timer. The POWER PET is smart enough to know exactly when it's
time to close
AUTOMATIC SAFETY RETRACT: Your POWER PET PX is intrinsically safe for all pets and people, including small
children. The door panel weighs less than 2 lbs. and is closed smoothly by gravity (not the motor) and is too light to cause
any physical injury. However, just to be doubly safe around infants, we've included an automatic safety retract feature.
This feature causes the panel to instantly retract if it encounters an obstruction during closure.
DEFEATING THE AUTOMATIC SAFETY RETRACT: Under unusual conditions, such as a warped wall mounting, the
door sometimes may close so slowly that the auto-retract feature triggers the door to re-open unnecessarily. In these
cases it may be desirable to defeat the Automatic Safety Retract feature. Do this by first pressing the OFF button to
turn off the door controls and all the lights. Leave the door powered by the wall wart or battery when you do this. Then
while holding down the MANUAL OPEN button, press and release the OUTSIDE SENSOR button. The OUTSIDE light
will blink to indicate the feature has been disabled.
ENABLING AUTOMATIC SAFETY RETRACT: Similarly you may enable the Automatic Safety Retract feature at any
time. Do this by first pressing the OFF button to turn off the door controls and all the lights. Leave the door powered by
the wall wart or battery when you do this. Then while holding down the MANUAL OPEN button, press and release the
INSIDE SENSOR button. The INSIDE light will blink to indicate the feature has been enabled. When shipped from the
factory, the automatic safety retract feature is enabled.
After Defeating or Enabling the feature, press the POWER ON button to resume normal door operation.
PET COLLAR OPERATING INSTRUCTIONS
Your POWER PET DOOR comes with a standard model MS-2 or MS-2A ultrasonic transmitter collar. Each collar includes
a battery TEST button which illuminates a red LED when the battery is OK. If the LED fails to light, battery replacement is
necessary.
Note: Each model of collar has a different signal strength, and requires a slightly different adjustment of the RANGE
knobs on the door. If you have more than one pet using the door make sure they are all wearing the same model of col-
lar, so a single range setting works for all pets.
If you upgrade to the multi-function RX-10 collar on one pet, we recommend you use an RX-10 collar or an MS-2A col-
lar on any other pets that need access to the door.
ADJUSTING THE STRAP
1. Fasten the collar around your pet's neck so that it fits comfortably. In most cases there will be excess strap length.
2. With a soft pencil or magic marker, mark the amount of strap to be removed leaving at least one inch past the D-ring
buckle.
3. Remove the collar from your pet and cut off the excess strap at the mark.
4 To avoid fraying of the cut end, heat may be applied.
5. Re-fasten the collar around your pet's neck so that it hangs loosely and comfortably
REPLACING THE MS-2 or MS-2A BATTERY
1. To open the unit, place a small flat screwdriver or other flat object into either end slot and twist. The collar will snap open.
2. Slowly separate the two halves while observing how the battery is suspended between a wire braid and a spring on the
board. Remove battery and replace with a new battery, paying attention to install in the same location and orientation.
______________________________________________________________________________________________________________________________________
8
www.hightechpet.com
High Tech Pet Products, Inc.