Dynasty DYN-4401 Einbauanleitung

Blättern Sie online oder laden Sie pdf Einbauanleitung für Türöffnungssystem Dynasty DYN-4401 herunter. Dynasty DYN-4401 2 Seiten.

PARALLEL ARM INSTALLATION
CLOSER MOUNTED ON DOOR ON PUSH SIDE
This drawing shown is RIGHT HAND DOOR, For LEFT HAND DOOR should be install in symmetry
1-11/16" 1-11/16"
(43)
(43)
1-1/16" 1-1/16"
(27)
(27)
4 Holes for self
drilling/tapping screws or
1"
3"
1"
1
-20 Machine Screws.
4
(76.2)
(25.4)
(25.4)
FOREARM
30°
SCREW
SHOE
PARALLEL
BRACKET
ARM SCREW
BACKCHECK
SCREW
MAIN SPEED
SCREW
LATCH
SPEED
SCREW
BACKCHECK
SELECTOR
VALVE SCREW
* Delayed Action
Page 4
Do not scale drawing
Dimensions are in inches (mm)
5 Holes for self
drilling/tapping screws or
1
-20 Machine Screws.
4
A
"A"
OPENING
9-
7
"
16
TO 100°
(240)
5
8
"
8
* TO 120°
(220)
7
7
"
8
* TO 180°
(200)
* Recommended mounting for
meeting ADA compliance
* When door closer is installed and
adjusted to conform to ADA reduced
opening force requirements (5 lbs max.),
it may not have adequate closing force to
reliably close and latch the door.
B
1. Select degree of opening and use dimensions shown or attached template to
locate 4 holes on door for closer body and 5 holes on door for parallel bracket.
2. Prepare door and frame for fasteners. See "Preparation for Fasteners",
Figure 1, Page 1.
3. Before installation, turn Backcheck selector valve (Found on the
opposite side of closer ) ALL THE WAY IN(CLOCKWISE).
2. Adjust spring power to match door width as indicated by chart on page 1.
3. Mount clo ser on door as dimensions shown. Tube end toward latch.If pivots are
used, locate closer and parallel bracket from CENTERLINE OF PIVOT.
4. Place open end wrench on bottom shaft and turn toward hing e jamb about 30 °
and then place main arm on top shaft, insert arm screw into top of shaft and
tighten.
5. Attach parallel bracket on frame using dimensions shown.
6. Attach rod and shoe to parallel bracket as shown.
7. Insert rod in to forearm, and adjust the length of the forearm so that the main arm
is parallel to door. Then insert forearm set screw and tighten.
(IF HOLD OPEN ARM IS USED, THE NUT IS ON THE TOP FOR RH DOOR AND
BOTTOM FOR LH DOOR)
REGULATION:
A ' normal ' closing time from 90 ° open position to door stop position is 4-6 sec onds,
evenly d ivided between main swing speed and latch swing speed. Use
(Furnished) to adjust speed. To slow m ain speed of door, turn regulating screw nearest
shaft clockwise. To slow latch speed, turn regulating screw nearest hing e clockwise.
BACKCHECK AND DELAYED ACTION
To increase back-check force, turn regulating screw clockwise.
DO NOT USE ABRUPT BACKCHECK OR EXPECT DOOR CL OSER TO ACT AS A
DOOR STOP.
To Increase the Delayed closing time, turn the DA screw clockwise.
COVER
Place insert in Proper cutout, then push cover aga inst door. Tighten both cover screw
securely.
HOLD OPEN ADJUSTMENT (WHEN FRICTION HOLD OPEN ARM IS USED)
Loose adjusting nut, open door to required hold open position and tighten the nut.
Do not permit door to swing beyond hold open setting.
STANDARD MOUNT
(PULL SIDE)
Preparation for Fasteners-Figure 1.
"B"
TOOLS REQUIRED
1
8-
"
16
(205)
5
7 -
"
16
(185)
6- 1/2"
(165)
Spring power setting & door width
MAXIMUM
DOOR WIDTH
EXTERIOR
INTERIOR
DOORS
DOORS
5 lbs-ADA
8.5 lbs-ADA
34"(864)
38"(962)
30" (762)
36"(914)
48"(1219)
42"(1067)
54"(1372)
48"(1219)
60"(1524)
DOOR CLOSING
AND OPENING
CONTROL
Allen key
F
Latch
S
Closing
F
S
2
1
*DA
BC
DYN-4401 DOOR CLOSER
INSTALLATION INSTRUCTIONS
Grade 1, Meets ANSI A 156.4
TOP JAMB MOUNT
(PUSH SIDE)
METAL
WOOD
Self Drilling /Tapping
Wood and Metal
For wood, drill 3/16" hole
Machine Screws
3/16"
#7
*Pilot Hole Required
#7 Drill, 1/4"-20 Tap
1/4"-20
FULL
TURNS
REQUIRED
5 TURNS C.C.W.
2 TURNS C.C.W.
0 TURNS
5 TURNS C.W.
10TURNS C.W.
15 TURNS C.W.
C.W-Clockwise
C.C.W-Counter-Clockwise
*Delayed
Action
F
Back
S
F- Fast
Check
S-Slower
*Optional
Spring Power Nut
PARALLEL MOUNT
(PUSH SIDE)
Sleeve Nut and Bolt
screws
Drill 9/32" thru from
Closer side
3/8" Drill other Side
Check building and fire
codes to see if your
application requires the
use of sleeve nuts and
bolts.
LEFT
RIGHT
HAND
HAND
DOOR
DOOR
HOW TO DEFINE HAND OF DOOR.
Caution: Do not back valves out of closer or
a leaking will result.
ATTENTION:
Adjust closing time between 4 to 6
seconds from 90°.Use of the door
by handcapped,elderly or small
children may require longer closing
time.
Backcheck("BC") valve controls the
hydraulic resistance to door opening
in backcheck range. NEVER close
this valve completely.
it is not to provide a positive stop.
Page 1