Dynasty Spas 9919-100418-B Schnellreferenzkarte
Blättern Sie online oder laden Sie pdf Schnellreferenzkarte für Whirlpool Dynasty Spas 9919-100418-B herunter. Dynasty Spas 9919-100418-B 2 Seiten. Neptune series
Seite drucken
The Quick Reference Card provides a quick overview of your spa's main
functions and the operations accessible with your digital control pad.
SC-MP-DY1 / Dual-Pump System
Starting Pump 1:
Press Pump 1 to turn Pump 1 on at low speed.
Press a second time to turn pump to high speed.
Press a third time to turn pump off. When at high
speed, a built-in timer turns pump off after 20 min-
utes and when at low speed after 2 hours, unless
manually deactivated first.
The "Pump 1" indicator lights up
when Pump 1 is on at high speed.
It flashes when Pump 1 is on at low
speed.
Starting Pump 2:
Press Pump 2 to turn Pump 2 on. Press a second
time to turn Pump 2 off. A built-in timer automati-
cally turns pump off after 20 minutes, unless pump
has been manually deactivated.
The "Pump 2" indicator lights up
when Pump 2 is on.
Setting water temperature:
Use Up or Down arrow keys to regulate water
temperature. The temperature setting will be
displayed for 5 seconds to confirm your new
selection.
The "Set Point" indicator displays the
desired temperature, NOT the current
water temperature!
Water temperature can be adjusted by 1˚ in-
crements from 59 to 104˚F (15 to 40˚C).
Temperature display unit:
Press and hold Light key for 5 seconds to display
water temperature in either Fahrenheit (˚F) or
Celsius (˚C). If a power-up occurs, system re-
turns to default setting (˚F).
Quick Reference Card
Turning the light on:
Neptune Series Spas feature an easy-to-change selection of nine
different LED color/display settings. To activate the LED lights,
press the "LIGHT" button on the topside panel one time. To
advance to the next color/display setting, press the "LIGHT" button
twice in a row. The LED's will go off with the first press, then back
on in the next setting with the second press. If the LED's remain off
for more than 5 seconds, the color/display sequence will reset and
start back at the beginning the next time the "LIGHT" button is
pressed. The color/display sequence is:
Setting #1 LED's light up and slowly cycle throught all six color.
The slow cycle then restarts at the beginning and repeats.
Setting#2 LED's light up and remain on in Aqua.
Setting#3 LED's light up and remain on in Purple.
Setting#4 LED's light up and remain on in Blue.
Setting#5 LED's light up and remain on in Gold.
Setting#6 LED's light up and remain on in Green.
Setting#7 LED's light up and remain on in Red.
Setting#8 LED's light up for 2 sec, flash off, then flash on in the
next color, until all six colors have been displayed. The flashing
cycle then restarts at the beginning and repeats.
Setting#9 LED's flash on/off quickly, for a strobe light effect.
The LED lights will automatically turn themselves off after 2 hours
in any one setting.
Automatic water heater start:
When water temperature is 1˚F (0.5˚C) lower
than the Set Point, the heater will automatically
turn on until water temperature reaches Set Point
plus 1˚F (0.5˚C).
The "Heater" indicator lights up when
the heater is on. It flashes when there
is a request for more heat but the heater
has not yet started.
N.B.: If your system is configured in Low Current Mode,
the heater will not start if a pump is on at high speed.
Economy mode:
Press Econo key to switch from Normal mode to
Economy mode. In Economy mode, system main-
tains temperature at the desired Set Point during
filter cycles only. Set Point is 20˚F (11˚C) below
the Normal mode Set Point for the rest of the
time. In Economy mode, the display will toggle
between the current water temperature and the
"Econ" message.