HIKOKI H 3641DA Handhabungshinweise Handbuch - Seite 12

Blättern Sie online oder laden Sie pdf Handhabungshinweise Handbuch für Elektrowerkzeug HIKOKI H 3641DA herunter. HIKOKI H 3641DA 20 Seiten.

Seite drucken

○ When the battery charger has been continuously used,

the battery charger will be heated, thus constituting the

cause of the failures. Once the charging has been

completed, give 5 minutes rest until the next charging.

(2) Regarding the temperatures and charging time of the

battery (See Table 2)

Model

Type of battery

Charging voltage

Temperatures at which the

battery can be recharged

1.5 Ah

2.0 Ah

2.5 Ah

Charging time for

3.0 Ah

battery capacity,

approx. (At 20°C)

4.0 Ah

5.0 Ah

6.0 Ah

1.5 Ah

(× 2 unit)

Charging time for

multi volt battery

2.5 Ah

capacity, approx.

(× 2 unit)

(At 20°C)

4.0 Ah

(× 2 unit)

Number of battery cells

Charging voltage for USB

Charging current for USB

Weight

NOTE

○ The recharging time may vary according to the ambient

temperature and power source voltage.

○ If charging takes a long time

–

Charging will take longer at extremely low ambient

temperatures. Charge the battery in a warm location

(such as indoors).

–

Do not block the air vent. Otherwise the interior will

overheat, reducing the charger's performance.

–

If the cooling fan is not operating, contact a HiKOKI

Authorized Service Center for repairs.

4. Disconnect the charger's power cord from the

receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after

use, and then keep it.

Table 2

UC18YSL3

Li-ion

14.4–18 V

0°C–50°C

15 min

20 min

25 min

20 min

(BSL1430C, BSL1830C:

30 min)

26 min

(BSL1840M: 40 min)

32 min

38 min

20 min

32 min

52 min

4–10

5 V

2 A

0.6 kg

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries and

batteries that have not been used for an extended period is

not activated, the electric discharge might be low when

using them the first and second time. This is a temporary

phenomenon, and normal time required for recharging will

be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become completely

exhausted. When you feel that the power of the tool

becomes weaker, stop using the tool and recharge its

battery. If you continue to use the tool and exhaust the

electric current, the battery may be damaged and its life

will become shorter.

(2) Avoid recharging at high temperatures. A rechargeable

battery will be hot immediately after use. If such a

battery is recharged immediately after use, its internal

chemical substance will deteriorate, and the battery life

will be shortened. Leave the battery and recharge it

after it has cooled for a while.

MOUNTING AND OPERATION

Action

Removing and inserting the battery

Charging

Remaining battery indicator

Inserting SDS-max tools

Removing SDS-max tools

Deciding working position of tool

Installing the side handle

Switching on and off

Locking-on the On/Off switch

Releasing the On/Off switch

Impact rate change*

How to use the demolition hammer*

How to use the LED light

Cleaning of the battery installation

compartment

Charging a USB device from a

electrical outlet

Charging a USB device and battery

from a electrical outlet

How to recharge USB device

When charging of USB device is

completed

Selecting accessories*

*1 When conducting chipping operations or alignment

operations, change the tool's impact rate in accordance

with the task by using the impact rate selector switch.

Figure

16-a

16-b

―

Page

16, 17