HIKOKI SB3608DA Handhabungshinweise Handbuch - Seite 11

Blättern Sie online oder laden Sie pdf Handhabungshinweise Handbuch für Elektrowerkzeug HIKOKI SB3608DA herunter. HIKOKI SB3608DA 20 Seiten.

Seite drucken
Lock
Switch locks to the "ON" position
Lock
Unlock
Warning
Battery
Lights ;
The battery remaining power is over 75%
Lights ;
The battery remaining power is 50%–75%.
Lights ;
The battery remaining power is 25%–50%.
Lights ;
The battery remaining power is less than 25%
Blinks ;
The battery remaining power is nearly empty.
Recharge the battery soonest possible.
Blinks ;
Output suspended due to high temperature.
Remove the battery from the tool and allow it to
fully cool down.
Blinks ;
Output suspended due to failure or malfunction.
The problem may be the battery so please
contact your dealer.

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the
accessories listed on page 15.
Standard accessories are subject to change without notice.
APPLICATIONS
○ Finish sanding and fi nish fl ooring of woodwork products.
○ Base polishing of wood-coated surfaces.
○ Finish sanding of metal surfaces.
○ Base polishing of metal-coated surfaces, rust removal,
or paint removal prior to refi nishing.
○ Surface fi nishing of slate, concrete, and similar materials.

SPECIFICATIONS

1. Power tool
Model
Voltage
No-load belt speed
Sanding belt size
Battery available for this
tool*
Weight
*
Existing batteries (BSL3660/3620/3626, BSL18 series,
etc.) cannot be used with this tool.
SB3608DA
36 V
122–450 m/min
76 × 533 mm
Multi volt battery
4.2 kg (BSL36A18)
4.5 kg (BSL36B18)
NOTE
Due to HiKOKI's continuing program of research and
development, the specifi cations herein are subject to
change without prior notice.
Electronic control
○ Braking Function
Brake is activated when the switch is turned off , stopping
the motor's rotation.
○ Soft start
○ Variable speed
○ Constant speed
○ Overload protection
This protection feature cuts off the power to the motor
in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been
activated, the motor may stop.
In this case, release the tool switch and eliminate causes
of overloading.
After that you can use it again.
○ Overheat protection
This protection feature cuts off the power to the motor
and stops the power tool in the event of overheating of
motor during operation.
When the overheat protection feature has been
activated, the motor may stop.
In this case, release the tool switch and cool it down in a
few minutes.
After that you can use it again.
○ Restart prevention function
When the power is still switched on, the tool will not
restart when a battery is installed. This function can be
canceled once the tool is switched off .
2. Battery
Model
Voltage
Battery capacity
*
The tool itself will automatically switch over.
CHARGING
Before using the power tool, charge the battery as follows.
1. Connect the charger's power cord to the receptacle.
When connecting the plug of the charger to a receptacle,
the charge indicator lamp will blink in red (At 1- second
intervals).
2. Insert the battery into the charger.
Firmly insert the battery into the charger as shown in
Fig. 3.
3. Charging
When inserting a battery in the charger, the charge
indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge
indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table 1, according to the condition of the
charger or the rechargeable battery.
11
BSL36A18
36 V / 18 V
(Automatic Switching*)
2.5 Ah / 5.0 Ah
(Automatic Switching*)