Corby PLATINUM 7520 Installations- und Programmieranleitung

Blättern Sie online oder laden Sie pdf Installations- und Programmieranleitung für Tastenfeld Corby PLATINUM 7520 herunter. Corby PLATINUM 7520 4 Seiten.

Seite drucken

PECIFICATIONS

%¸

Input Voltage: 12-24 Volt DC or 12 Volt AC

%¸

Power Consumption: 120mA max @ 24 VDC, 20mA idle

3A Power Supply is recommended for use with

NOTE:

door strike or magnetic lock

%¸

Programmable Relay:

rated at 2A @ 30VDC (inductive load)

%¸

Operating Temperature:

-40

C to 125

C (-40

F to 257

%¸

Available Models with Inst alled Dim ensions:

%¸

7510:

Single-Gang Style Keypad

3.20" W X 5.10" H x 0.75" D

%¸

7520:

Mullion Surface-Mount Keypad

1.75" W X 7.125" H x 1.00" D

%¸

7530:

Mullion Mortise-Mount Keypad

1.75" W X 7.125" H x 0.25" D

%¸

User Codes: Up to 200 unique codes including

1 master code. Codes will be between 4 and 8

digi ts in length. Codes are st ored in nonvolat ile

EEPROM memory.

%¸

Lockout Feature: Keypad will lock out all

funct ions for 30 seconds after three consecutiv e

invalid codes.

%¸

Factor y Default Sett ings:

%¸

Master code 1 2 3 4

%¸

User code

5 6 7 8 9 0

%¸

Relay Time 5 seconds (Momentary)

HYSICAL

ESCRIPTIONS

LED Explanation:

%¸

Green LED:

%¸

Steady off = D oor rel ay deactiva ted

%¸

Steady on = Doo r rela y acti vated

%¸

Red LED:

%¸

Normal Operation:

Three sec onds on = Inv alid code

entered.

ii)

Slow flash = 30 second delay due to

three consecutive invalid codes entered.

%¸

Progr amm ing Mode:

Slow flash = Program standby, ready to

accept new function.

ii)

Fast flash = Program in progress,

awaiting input.

iii) Very fast flash = Erasing all user codes.

Form C, dry contacts

LATINUM

NSTALLATION AND

VAILABLE

ODELS

Model 7510

(Front)

Model 7520

Model 7530

(Front)

(Side)

7500 K

ERIES

ROGRAMMING

Enter Programming Mode ** (master code) **

Example:

** 1234 **

Programming Functions:

Set Relay to M omentary

1 (time in seconds) #

Example:

1 05 # (Sets to 5 secs)

Set Relay to Latch

1 00 #

Add New User

2 (user n umber) # (user

code) # (user code) #

Example:

2 002 # 22222 # 22222 #

Change Existing User

2 (user n umber) # (user

code) # (user code) #

Example:

2 002 # 23456 # 23456 #

Change Master Code

2 0 # (new master code) #

(new master code) #

Example:

2 0 # 382436 # 382436 #

Erase a User Code

3 (user code) #

Example:

3 23456 #

Erase All Users

4 (master code) #

Example:

4 382436 #

Note: New Master Code must be between 4 & 8 digits.

Option 4 erases all User Codes, but not the

Master C ode.

Wire Connections:

%¸

Power - Connect either a 12 - 24 volt direct

current (DC) or a 12 volt al ternating current (AC)

power supply to these terminals. Polarity does not

matter, as the keypad has been designed to work in

both directions. Power supplies outside this range

may cause permanent damage to the keypad.

%¸

Common - This terminal is the Common output

of the relay and is used in conjunction with the

N.O. or N.C. Terminals (see below) to control a

door lock.

%¸

N.O. - This term inal is the Norm ally Open

outpu t of t he relay . In a n orm al locked st ate,

this terminal is disconnected from the Common

terminal. In an unlocked state, this terminal is

connected to the Common terminal.

%¸

N.C. - This term inal is the Norm ally Closed

outpu t of t he relay . In a n orm al locked st ate,

this terminal is connected to the Common

terminal. In an unlocked state, this terminal

disconnects from the Common terminal.

%¸

Reset Button - This button is used to reset the

master code back to its factory default. Follow

the instructio ns out lined in the Programming

section, under Factory Reset Function.

EYPAD

NSTRUCTIONS

UICK

UIDE