HIKOKI WH 18DD Handhabungshinweise Handbuch - Seite 8

Blättern Sie online oder laden Sie pdf Handhabungshinweise Handbuch für Schlagschrauber HIKOKI WH 18DD herunter. HIKOKI WH 18DD 11 Seiten.

Seite drucken

English

Before charging

While charging

Charging

Pilot lamp

complete

(red)

Overheat

standby

Charging

impossible

● Regarding the temperatures and charging time of the

battery.

The temperatures and charging time will become as

shown in Table 2.

Charger

Battery

Charging voltage

Weight

Temperatures at which the

battery can be recharged

Charging time for battery

capacity, approx. (At 20C)

1.5 Ah

2.0 Ah

2.5 Ah

3.0 Ah

4.0 Ah

5.0 Ah

6.0 Ah

8.0 Ah

Number of battery cells

NOTE

The recharging time may vary according to temperature

and power source voltage.

CAUTION

When the battery charger has been continuously used,

the battery charger will be heated, thus constituting

the cause of the failures. Once the charging has been

completed, give 15 minutes rest until the next charging.

4. Disconnect the charger's power cord from the

receptacle.

5. Hold the charger  rmly and pull out the battery.

NOTE

Be sure to pull out the battery from the charger after use,

and then keep it.

CAUTION

○ If the battery is charged while it is heated because it has

been left for a long time in a location subject to direct

sunlight or because the battery has just been used, the

pilot lamp of the charger lights for 1 second, does not

light for 0.5 seconds (oﬀ for 0.5 seconds). In such a case,

 rst let the battery cool, then start charging.

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for

Blinks

0.5 seconds. (oﬀ for 0.5 seconds)

Lights continuously

Lights

Lights for 0.5 seconds. Does not light for

Blinks

0.5 seconds. (oﬀ for 0.5 seconds)

Lights for 1 second. Does not light for

Blinks

0.5 seconds. (oﬀ for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

Flickers

0.1 seconds. (oﬀ for 0.1 seconds)

Table 2

UC18YKSL

14.418

0.35

0C50C

min.

120

min.

150

min.

180

min.

240

410

Table 1

○ When the pilot lamp  ickers (at 0.2-second intervals),

check for and take out any foreign objects in the charger's

battery connector. If there are no foreign objects, it is

probable that the battery or charger is malfunctioning.

Take it to your authorized Service Center.

○ Since the built-in micro computer takes about 3 seconds

to con rm that the battery being charged with charger

is taken out, wait for a minimum of 3 seconds before

reinserting it to continue charging. If the battery is

reinserted within 3 seconds, the battery may not be

properly charged.

MOUNTING AND OPERATION

Action

Removing and inserting the

battery

Charging

Mounting the bit

Reversing the rotational direction

Switch operation

How to use the LED light

Mounting and removing the hook

(sold separately)

Remaining battery indicator

Selecting accessories

LED LIGHT WARNING SIGNALS

This product features functions that are designed to protect

the tool itself as well as the battery. While the switch is

pulled, if any of the safeguard functions are triggered

during operation, the LED light will blink as described in

Table 3. When any of the safeguard functions are triggered,

immediately remove your  nger from the switch and follow

the instructions described under corrective action.

Battery overheated. Unable

to charge. (Charging will

commence when battery cools)

Malfunction in the battery or

the charger

Figure

Page

―