Majestic fireplaces UVC36 Installations- und Betriebsanleitung für Hausbesitzer - Seite 6

Blättern Sie online oder laden Sie pdf Installations- und Betriebsanleitung für Hausbesitzer für Gas-Heizung Majestic fireplaces UVC36 herunter. Majestic fireplaces UVC36 20 Seiten. Vermont castings vent-free gas room heaters homeowner's installation and operating manual

Seite drucken

Majestic Fireplaces

UVC / UVS Vent-Free Heaters

Mantels

Depending on the width of the mantel it may be in-

stalled higher or lower from the combustion chamber

opening. This also applies to the distance between the

mantel leg (if installed) and the ﬁreplace. Refer to Fig-

ures 3a and 3b for correct mounting heights and widths

for combustible mantels and mantel legs.

Noncombustible mantels and legs may be installed at

any height above the appliance opening.

When using paint or lacquer to ﬁnish the

mantel, such paint or lacquer must be heat

resistant to prevent discoloration.

Hearth Extension

A hearth extension in front of heater is recommended

but not required.

Planning

Planning the installation is an important ﬁrst step: it will

save time and money later in the actual installation. In

planning the installation, consider:

1. Where the heater will be located.

2. All components needed to complete the

project.

Mounting the Heater

The heater should only be mounted on the following

surfaces:

• A ﬂat combustible (burnable) surface.

• A raised wooden platform.

• A concrete block or other solid object placed be-

neath each of the four corners of the heater.

To mount the heater:

1. Choose unit location.

2. Place unit in position and secure to ﬂoor with 1¹⁄₂"

screws, or nails. The holes to secure the unit to the

ﬂoor are located just behind the bottom louvre on the

left and right hand side of the unit.

3. Frame in heater with a header across the top. It is

important to allow for ﬁnished face when setting the

depth of the frame.

4. Attach heater to frame using adjustable frame drywall

strips (located behind access door for shipping). Preset

depth to suit facing material (adjustable to 1/2" , 5/8" or

3/4" depths). (Fig. 4)

5. Use existing screws in side of unit to attach drywall

strip. Measure from face of heater to face of drywall

strip to determine ﬁnal depth. (Fig. 4)

Fig. 4 Adjustable drywall strip (nailing ﬂange).

Framing

FP1023

Framing can take place before or after the heater is set

side nailing flange

in place. The framing should be positioned to accom-

1/27/00 djt

modate the wall covering and facing material. Framing

material should be 2x4 or heavier. Framing headers

may rest on top of heater. (Refer to Page 4, Figures 1

and 2 for heater and framing dimensions.)

Insulating for Cold Climates

When a heater is installed in a chase or an outside wall,

the enclosure should be insulated like any other wall

of the home. Insulation should be installed under the

heater and on the inside of the exterior walls. (Fig. 5)

NOTE: Insulating for cold climates is strictly a recom-

mendation and not a requirement.

Insulation

methods

shown are

optional for

cold climate,

not a require-

ment for unit

operation.

Fig. 5 Insulating for cold climates.

Adjustable Drywall Strip

(Nailing Flange)

Scew

Drywall

Position

Depths

1/2" (13 mm)

5/8" (16 mm)

3/4" (19 mm)

Adjustable

1/2", 5/8" & 3/4"

Spacing

FP1023

FP456

GF456

UVC

2/19/97

20000135