KitchenAid 30" Freestanding Range Einbauanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Einbauanleitung für Kochfeld KitchenAid 30" Freestanding Range herunter. KitchenAid 30" Freestanding Range 5 Seiten. (61cm), (68.6cm), and (76.2cm) indoor/outdoor electric warming drawer
Auch für KitchenAid 30" Freestanding Range: Installationsanleitung Handbuch (8 seiten), Einbauanleitung (5 seiten), Installationsanleitung Handbuch (13 seiten), Installationsanleitung Handbuch (16 seiten)

Seite drucken

Four-wire electrical connection:

ing

8. Remove the grounding-link screw from the range

frame. Save the grounding-link screw. Bend up the

grounding link so that it does not contact the range.

See Figure 8.

bare

wire

from

powe

suPPI

cable

grounding-

link screw

9. Connect the bare grounding wire from power supply

cable to the range using the grounding-link screw.

The grounding wire must be attached first and

must not contact any other terminal. See

Figure 9

silver-colored

bare wire

from power

supply

cabl

connector

and

Figure 10

wg:r

supply

IO. Connect the neutral wire (white wire) to the center,

silver-colored terminal screw on the terminal block

using the brass nuts that are attached to the

terminal block cover. See Figure 10.

Il. Connect the other two wires to the outer terminals

on the terminal block. See Figure 10.

12. Do NOT loosen the factory installed nuts already

on the terminal. Tighten nuts with 3/8" nut driver for

proper electrical connection.

13. Tighten the locking ring and clamping screws of the

conduit connector.

14. Replace the terminal block cover.

Three-wire electrical

connection:

Use this method ONLY if local codes PERMIT

connecting cabinet-grounding

conductor to neutral

wire of power supply cable.

3. Use the brass terminal nuts attached to the

knockout opening to connect the neutral wire (white

wire) to the silver-colored terminal screw on the

terminal block. See Figure 11.

3. Connect the other two wires to outer terminal

screws on the terminal block. See Figure 11.

IO.Do Not loosen factory-installed

nuts already on the

terminal. Tighten nuts with 318" nut driver for proper

electrical connection.

I1 .Tighten the locking ring and clamping screws of the

conduit connector.

12,Reinstall the terminal block cover.

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to follow this instruction can result in back

or other injury.

18.1

Firmly grasp the range and gently lay it on its

back on the cardboard corners.

Pull cardboard bottom and shipping base firmly

to remove.

110

Place cardboard or hardboard in front of

range. Stand range back up onto cardboard

or hardboard.

Panel C

Tip Over Hazard

Connect anti-tip bracket to the

range.

Reconnect anti-tip bracket, if

the range is moved.

Do not push down on the

open oven door.

Follow the installation

instructions.

Do not let children climb onto

the oven door.

Failure to follow these

instructions

can result in

death, burns, or other injury.

Electrical Shock Hazard

Take special care when drilling holes into the

Press on front of

floor. Electrical wires or plumbing may be located

storage drawer

beneath floor.

and release to

Locate the electrical circuits that could be

affected by the installation of this bracket and

turn off power to these circuits.

Failure to follow these instructions may result in

death, fire or electrical shock.

II 1 =I

Place the anti-tip bracket

template on the floor in the

cab/net opening so that the

left edge is against cabinets

and the top edge is against

the rear wall, molding or

cabinet.

f il

25"

countertop

over 24"

cabinet

If countertop opening is

deeper than 25 inches,

measure and mark a

distance 25 inches in from

front of

countertop

opening

and align

template with mark (or

subtract 25 inches from

countertop depth and add

the difference to the

corresponding dimension).

If countertop is not flush to

the side of cabinet

opening, align the left side

of the template to allow for

the countertop overhang.

Tape the range anti-tip

bracket template in place.

Countertop

overhangs

'cabinet

side.

Insert storage drawer into slide rails on sides

of drawer opening. Lift front of drawer

slightly and push firmly to close drawer.

120

Push in and

turn each

surface unit

A = Difference

control knob to "HI"

between

position. Check the

countertop

irth

and

operation of the cooktop

elements and indicator lights.

Contact a qualified floor covering installer for the

best procedure of drilling mounting holes through

your type floor covering.

Before moving, slide range onto cardboard or

hardboard.

To mount

anti-tip

. bracket to

wood floor,

use the anti-tip bracket

template to mark where to

drilfmounting holes. Use a

drill with a 118" drill bit to

drill the two holes. Remove

template from floor.

To mount anti-tip bracket

to concrete or ceramic

floor,

use the anti-tip

bracket template to mark

where to drill mounting holes. Use a drill with a 3/16"

masonry drill bit to drill the two holes. Remove template

from floor. Tap plastic anchors into mounting holes in

floor with hammer.

Line up holes in anti-tip

bracket with holes in floor.

Use the screws provided to

fasten anti-tip bracket to floor.

NOTE: Anti-tip bracket must be mounte

securely to the sub floor.

Depending on the thickness of

your flooring, longer screws

may be necessary to anchor

the bracket to the sub floor.

Longer screws are available

from your local hardware store.

Move range close to cabinet opening.

Plug power supply cord into grounded outlet

or connect power supply cable to junction

box. See "Electrical requirements," panels A and B for

details. "88:88" should appear in the clock display.

Remove cardboard or hardboard from

under range. Carefully move range

open. Pull open

to first stop position7

Lift front of drawer to clear white

wheels in drawer guides. Remove drawer

and set it aside on a protected surface.

)17

Look under range (a

flashlight may be

needed) to check that

left rear leveling leg is engaged in

the anti-tip bracket. If leveling leg is

not properly engaged, remove and

reposition the anti-tip bracket to

insure that the leveling leg fits properly in the anti-tip

bracket.

Place rack in oven. Place le

rack, first side to side; then front to back. If the range

' '

is not level, pull range forward until the rear leveling leg is

removed from the anti-tip bracket. Adjust the leveling legs

up or down. Then slide range back into position. Check

that leveling leg is engaged in anti-tip bracket.

NOTE: Oven must be level for satisfactory baking

conditions.

OFF

1211

Press the "Clock Set" button. "TIME, HR

AND MIN" will light up in the display. "0:OO"

will appear and the ":" will be flashing. Press

the number buttons for the correct time of day. Press

"Stat-t/Enter" button to start the clock.

)22/

Check the operation of the oven element.

Press the "BAKE" button. "350"" will appear

In the temperature display. The ON, Bake

Element, Outer Broil Element and Oven Cavity symbols

will light up in the display. Press the "Start/Enter" button.

The bottom element should glow red and the indicator

light should be on. The upper element should become

hot but not glow red. The oven indicator light goes off

when the oven is preheated.

Press "Cancel/OFF" button.

B-l

Check the operation of the broil element.

Press the "BROIL" button. "500"" will appear

in the temperature display. The ON, Inner

and Outer Broil Elements and Oven Cavity symbols will

light up in the display. Press the "Start/Enter" button.

The top element should glow red and the indicator light

should be on.

Press the "Cancel/OFF" button.