KitchenAid GSU-42-E-2 Installationsanleitung Handbuch - Seite 6

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Kochfeld KitchenAid GSU-42-E-2 herunter. KitchenAid GSU-42-E-2 8 Seiten. 42" gas cooktop with broiler/griddle

Seite drucken

Check

air shutter

setting.

On natural

and LP gas there

should

a 3/4"

slot in burner

at both

top and bottom.

The

unit

is now ready

to plug service

cord

into

receptacle.

Make

sure

that

power

supply

neutral

is connected

to the wide

blade

slot

in receptacle.

is essential

that

the

electrical

outlet

which

the plug is connected

be properly

grounded

and polarized.

If this

is in doubt,

a qualified

electrician

should

be contacted

check

the outlet.

Initial

checks

are

made

either

with

or without

cooktop

de-

pending

upon

whether

or not the unit was converted

for LP gas,

1" OPENING

TOP AND

BOTTOM

Test

each

top

burner

one at a time

by setting

knob

to "light"

position.

This

is done

by pushing

in on knob

and turning

knob

to left or counterclockwise.

Repeat

at least

four

times.

A clicking

sound

should

be heard as soon as the knob

is turned

to "light"

position.

If it is not present,

turn

burner

"off"

and make

sure that

power

is being

supplied

to unit.

Check

to see that

service

cord

is firmly

place

in receptacle

or for a blown

fuse or tripped

circuit

breaker.

If these

are not at fault,

remove

knobs

and handles,

four

(4) screws

from

control

panel

to check

connec-

tions

at valve

switches.

Remove

left

rear drip

pan, burner,

and remove

module

cover

to check

connections

at spark

module.

Make sure that solid

gt-ound

connection

is made from

spark

module,

The

broiler-

burner

ignition

is checked

in the same manner

as the top burner,

Since

it must be done with

the

griddle

level with

the cooktop,

ignition

is observed

through

the right

hand opening

between

the griddle

and

the

cooktop.

If ignition

does not take

place,

remove

drip

pan in right

rear burner

and reduce

air shutter

opening.

After

all burners

have been

individually

checked,

reattach

top,

if it has been removed,

and put drip

pans in

place,

Recheck

top

burner

ignition

and make

initial

flame

adjustment

one burner

at a time.

If flames

lift

from

burner,

reduce

air shutter

opening;

if flames,

are yellow,

increase

operling,

until

3/8"

soft blue inner

cone is present.

Check

ignition

on each burner

at least four

(4) times.

If burner

fails

to light

and ignitor

is clicking,

turn

gas "off",

remove

drip

pan and recheck

flash tube

alignment.

A visual

check

should

made

to make

sure that

the ignitor

is producing

a spark.

If spark

not

present,

recheck

connections.

Should

failure

continue

after

these

checks,

reduce

air

shutter

opening.

Replace

drip

pan

and

check

ignition

again.

(Try

at least 4 times.)

Now

proceed

to check

ignition

on both

front

and back

burners

one time.

Sometimes

the air shutter

opening

must be adjusted

to get proper

ignition

when

the other

burner

is burning.

Repeat

check

four

(4) times

on each side as before.

LOW

FLAME

ADJUSTMENT

Top

Burners

Low

flame

adjustment

IS made by lighting

burner,

turning

knob

to "low"

and removing

knob,

Hold

base of

valve

stem

with

pliers

and

insert

narrow

(3/16")

standard

blade

screwdriver

in adjustment

screw

slot

(located

in center

of valve stem).

Turn

screw until

flame

is l/8"

long,

Replace

knob.

"Lo"

SETTING

VALVE

AIR SHUTI'J3R

ADJUSTMENT

SCREW

AIR SHIJTTER

SCREW

MANIFOLD

BURNER

VALVE

NEEDIE