Majorcom: RM-6000 Benutzerhandbuch - Seite 3

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Mikrofon Majorcom: RM-6000 herunter. Majorcom: RM-6000 5 Seiten. Remote microphone & wall volume controle for matrix px-6120

Seite drucken
4
RM-6000 | LM-6000
REMOTE MICROPHONE & WALL VOLUME CONTROLE FOR PX-6120
DIAGRAM OF THE FRONT AND REAR PANELS OF THE LM-6000 WALL CONTROLLER
1
3
4
5
6
7
8
(1)
DIP Configuration Switch
(2)
Connection terminal block (be careful to close the cover before wiring)
(3)
RS-485 A link
(4)
RS-485 B link
(5)
AUDIO + link
(6)
AUDIO Link –
(7)
Power Link +24VDC
(8)
GND
(9)
Top Source Selection
(10)
Bluetooth control
(11)
Down Source Selection
(12)
Display
(13)
Volume +
(14)
Volume -
User manual
5 6 , c h e m i n d e l a F l a m b è r e • 3 1 3 0 0 To u l o u s e • F R A N C E • T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 • c o m m e r c i a l @ m a j o r c o m . f r • w w w . m a j o r c o m . f r
2
9
10
11
12
14
13
REMOTE MICROPHONE & WALL VOLUME CONTROLE FOR PX-6120
CONNECTION AND CONFIGURATION
1.
The matrix amplifier has 5 input channels and a full multi-source audio player.
2.
Mic inputs 1, 2, and 3 are designed for mic or line level sources such as CD or MP3 players or
blender outputs. Thanks to the combo connector on the back panel, they can be switched via DIP switches.
3.
Can accept an XLR plug or 6.35mm jack (balanced or unbalanced signal).
4.
Supports up to 6 microphone panels and or up to 6 wall control panels.
5.
The connection setting must match the address. Please refer to the back panel or bottom case of
the device.
FOR DIP SWITCH SETTING
Change the sound source using the adjustment button on the front panel of the main unit or the touchscreen
button on the wall control panel.
DIP SWITCH
1.
The Mic /Line 1, 2 and 3 inputs each have 2 DIP switches set on the back panel and activate the
+48V phantom power condenser microphone.
2.
Set the correct level for the connected input source (MIC or line).
3.
If the connected source is a condenser microphone that requires phantom power, please make
sure the phantom channel is enabled.
4.
Be sure to disable these DIP switches when setting up the extender. Any change in the power
supply of the amplifier can cause loud noise in the system, which can damage the speaker.
5.
The DIP switches on the paging microphone and wall control panel are used to configure the
address to avoid conflicts.
THE MICROPHONE (RM-6000) SPEAKS TO THE FIRST SELECTION
1.
Press the Z1 key on the microphone (RM-6000), the call indicator lights up, and the host's digital
display displays C0; press the green CALL key to start talking.
If you need to speak throughoutthe zones, you can press the ALL button to quickly select all the
2.
zones, and then press the CALL button to start speaking. The LEDs on the main panel all display C0.
3.
If the microphone control (RM-6000) is not valid, please check if the composition code of the DIP
address switch on the back panel is correct, if it matches and if there is a conflict.
5 6 , c h e m i n d e l a F l a m b è r e • 3 1 3 0 0 To u l o u s e • F R A N C E • T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7
F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 • c o m m e r c i a l @ m a j o r c o m . f r • w w w . m a j o r c o m . f r
RM-6000 | LM-6000
5
Manuel d'utilisation