CeoTronics CT-DECT Base Betriebsanleitung - Seite 7

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Mikrofonanlage CeoTronics CT-DECT Base herunter. CeoTronics CT-DECT Base 14 Seiten. Headset for wireless duplex communication
Auch für CeoTronics CT-DECT Base: Betriebsanleitung (20 seiten), Betriebsanleitung (20 seiten), Betriebsanleitung (14 seiten), Betriebsanleitung (20 seiten)

Seite drucken

1. Switching On, Synchronization, Adjusting the Speaker Volume

If a third standard headset is subscribed into the base headset, the standard headset that was

subscribed in next to last is deleted from the data base of the base headset.

è NOTE

The base headset and the standard headset can also be used in conjunction with other

CeoTronics DECT units. The on-air subscription of a headset to one of these DECT units is

carried out analogous and in the sequence as described in sections 3.2....3.2.2. Going to do so,

first ascertain which of the DECT units is the base unit (lettering »CT-DECT Base«) and which a

standard unit (lettering »CT-DECT Standard«). For on-air subscription at a DECT unit always the

on/off switch and the push-button » ) ) « for subscription, connection setup and release are

used.

Please take heed of the special CeoTronics operating instructions for the DECT unit.

3.2

On-air subscription

è NOTE

Two standard headsets can never be simultaneously subscribed into the base headset, they

must always be subscribed one after the other. For subscription the base headset must always

be switched on before the standard headset.

3.2.1 On-air subscription of the first standard headset

On the base headset press the push-button » ) « (Fig. 1/d) and switch on the base headset by means

of the On/Off switch and volume control (rotary knob Fig. 1/c). After switching on keep the button » ) «

pressed for at least 10 seconds.

On the standard headset press the push-button » ) « (Fig. 1/d) and switch on the standard headset by

means of the On/Off switch and volume control (rotary knob Fig. 1/c). After switching on keep the

button » ) « pressed for at least 10 seconds. The standard headset has to be switched on within 2

minutes of the base headset being switched on, otherwise a »Time Out« may occur (see section 3.1).

After approx. 30 seconds a high double-beep tone can be heard both in the base headset and in the

standard headset. This indicates that the on-air subscription has been successfully completed. A

second high double-beep tone finally reports that the standard headset has synchronized itself with the

base headset.

3.2.2 On-air subscription of the second standard headset

Switch off (position »OFF«) the base headset and, if it is switched on, the second standard headset by

means of the On/Off switch and volume control (rotary knob Fig. 1/c).

Repeat the subscription procedure as described in section 3.2.1 for the base headset and for the

second standard headset.

Commissioning and operation

4.1

Putting on the headset and adjusting the microphone

a. Put on the headset. Adjust the headset muffs by sliding the headband so that the muff padding fully

encloses your ears and so that the headband is lying on the centre of your head. Only then is the

best possible noise attenuation provided.

For hygienic reasons we recommend that you use washable perspiration absorbers made of cotton

for the headset. These are pulled over the muff padding, making them comfortable to wear.

CAUTION

Do not »twist« the flexible swanneck. Do not carry the headset by the swanneck.

Use the microphone only with a windshield.