Gap Power Speedrooter 92R Betriebsanleitung - Seite 7

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Pfeifenreiniger Gap Power Speedrooter 92R herunter. Gap Power Speedrooter 92R 10 Seiten. For 3” through 10” (75mm-250mm)

Seite drucken
2.
Remove the V-Belt.
3.
Turn the drum clockwise with one
hand while pushing the cable into
the drum with the other.
4.
Be certain that the cable goes into
the drum in a clockwise direction as
you look at the front of the machine,
or the cable will tangle in the drum.
5.
Replace the V-Belt after cable is
installed.
Note: The cable should lay in the drum in a
clockwise direction.
HOW TO REMOVE DRUM
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE REMOVING DRUM FROM MACHINE!
1.
Remove belt guard by loosening the knob above the motor and
pulling the guard forward.
2.
Push the motor down far enough to slide the V-Belt off of the
drum.
3.
Remove the cutter and connecting screw from the cable end.
4.
Loosen the knob at the top of the Power Cable Feed.
5.
Unscrew knob behind the front post and pull the Power Cable
Feed off of the machine.
6.
With one hand on the cable, loosen
the knob on front post cap, then
open clamp. The Flexitube may
spring up out of the cap. (See Fig-
ure 1.)
7.
Use a 3/4" socket with extension to
loosen and remove the drum retain-
ing bolt.
8.
Tip the Speedrooter on its side.
9.
Remove the drum retaining bolt with
3/4" socket with extension.
10. Stand behind the machine, lift the frame slightly off the ground,
and slide the frame away from the drum until the drum is off the
shaft.
11. Then, roll the drum away from the machine.
HOW TO INSTALL DRUM
DISCONNECT MACHINE FROM POWER SOURCE
BEFORE INSTALLING DRUM ON MACHINE!
1.
Lay the machine frame on its side and roll the drum, with inner
drum installed, between the front post and drum shaft. Be sure
the front of the drum is facing the front post.
2.
While standing behind the frame, line the drum shaft up with the
hole in the back of drum, slightly lift the frame, and slide the drum
shaft into the back of the drum until it contacts the thrust washer
on the shaft. Make sure the needle roller bearings inside the hub
of the drum stay in place.
3.
Thread the drum retaining bolt into the drum shaft, just finger
tight.
Figure 1
7
4.
Stand the machine upright, then tighten the retaining bolt with a
3/4" socket with extension. (See Figure 2)
Figure 2
5.
Slide the V-Belt (62") over the drum and hang it from the slip
clutch. Push down on the motor enough to slide the V-Belt onto
the drum.
6.
Pull about 12" of cable out beyond the front post.
7.
Slide the Flexitube, spring end first, onto the cable and into the
inner drum. (See Figure 3)
Figure 3
8.
Then guide the knurled portion of the Flexitube spring into the
front post clamp. (See photo)
9.
With one hand on the cable in front
of the front post, push the cable
down to secure the Flexitube in
position with the clamp. Make sure
the Flexitube seats properly over
the guide pin in the base of the
clamp.
10. Then, close the clamp and tighten
the knob with your other hand.
11. Slide the Power Cable Feed over the cable and align the bolt
with the hole in the front post and the guide pins with the holes in
the clamp. When flush with the front post, secure with bolt and
washer behind the front post.
12. Slide the belt guard over the stud on top of the motor and tighten
the knob.
®
Speedrooter 92R