ALIBI ALI-BC1080P Handbuch zur Schnellinstallation - Seite 2

Blättern Sie online oder laden Sie pdf Handbuch zur Schnellinstallation für Sicherheitskamera ALIBI ALI-BC1080P herunter. ALIBI ALI-BC1080P 2 Seiten. Hd-tvi outdoor infrared bullet camera

Seite drucken

Drill a 3/4" hole through the mounting surface for the drop cable, if necessary.

Route the drop cable through the hole in the mounting surface, or through the cable guide in the

mounting base, then attach the camera assembly to the surface using the appropriate fasteners.

Connect the camera drop cable to video and power extension cables as required. NOTE: The

ALI-BC1080P camera includes both an HD-TVI and CVBS video drop cables.

Connect the other end of the video extension cable to a video monitoring device, such as a CCTV

system monitor or DVR.

Drop cable connectors are not waterproof.

NOTE

Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity

of the cable shown in the photo on page 1 of this guide.

Camera adjustments

Apply power to the camera.

Verify that video from the camera can be seen on the monitor.

While observing video from the camera, loosen the mounting bracket pan, elevation and horizontal

line adjustment lock screws, point the camera at your surveillance target, and then tighten

adjustment lock screws or nuts to hold the camera in position.

The mounting bracket pan adjustment can be made after loosening the lock nut (see the photo

below). Use a Phillips #1 screwdriver for the elevation and horizontal line adjustment lock screws.

Use for horizon line

adjustment

Camera mounting bracket adjustment

Cleaning

Clean the camera dome with an approved glass cleaning solution and a lint free cloth.

Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub

•

the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a

soft cloth.

Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.

•

These may cause damage to the surface over time.

Do not use benzene, thinner or other chemical products on the camera assembly; these may



dissolve the paint and promote damage of the surfaces. Before using any chemical product,

CAUTION

carefully follow the accompanying instructions.

www.observint.com

Use for

0° ~ 360°

elevation

adjustment

0° ~ 90°

0° ~ 360°

Specifications

Model

Image Sensor:

Signal System:

Effective Pixels:

Min. Illumination:

Shutter Time:

Digital Output:

Analog Output:

Lens:

Adjustment Range:

Day & Night:

Noise Reduction:

Synchronization:

Video Output:

Dynamic Range:

Operating Conditions:

Humidity:

Power Supply:

Power Consumption:

Weather Proof:

IR Range:

Dimension:

Weight:

Use for pan

adjustment

(lock nut)

Troubleshooting

Problem

Nothing appears on the screen

The video image is dim or not clear.

The screen is dark.

The camera is not working properly and the

surface of the camera is hot.

The image on the monitor flickers

ALI-BC1720P

ALI-BC1080P

1/3" CMOS

NTSC

1280(H) × 720(V), 1.3 mega pixel

1920(H) × 1080(V), 2.1 mega pixel

0.01 lux @ (F1.2, AGC on),

0 lux with IR

1/30 sec to 1/50,000 sec

HD-TVI (BNC)

CVBS (BNC)

3.6 mm

Viewing angle: 77°

Viewing angle: 80°

Pan: 0 - 360°, Tilt: 0 -90°, Rotation: 0 - 360°

True Day & Night ICR

Yes, IR Smart

Yes, 3D-DNR (IR Smart)

Internal synchronization

1 Vp-p composite output (75 Ω/BNC)

> 52 dB

-40 °F ~ 140 °F (-40 °C ~ 60 °C)

-4 °F ~ 140 °F (-20 °C ~ 60 °C)

90% or less (non-condensing)

12 Vdc ± 10%

3.5 W max.

IP66

up to 65 ft (20 m) approx.

Φ2.76" × 5.89" (Φ70 × 149.5 mm)

0.79 lbs (360 g)

Possible Cause

- Check the power connection.

- Check the video signal cable connection to the monitor.

- If the camera lens is dirty, clean it with a soft, clean cloth.

- Adjust the monitor controls, if necessary.

- If the camera is facing a very strong light, change the camera position.

- Adjust the lens focus.

- Adjust the contrast control of the monitor.

- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)

properly, and check the cable connections.

- Verify that the camera is correctly connected to an appropriate regulated

power source.

- Make sure that the camera isn't facing direct sunlight or fluorescent light.

If necessary,change the camera position.