ALIBI ALI-CD1720E Installationshandbuch - Seite 2
Blättern Sie online oder laden Sie pdf Installationshandbuch für Sicherheitskamera ALIBI ALI-CD1720E herunter. ALIBI ALI-CD1720E 2 Seiten.
6.
Anchor the mounting base to the ceiling with appropriate fasteners. If the camera drop cable will be
routed through a cable channel, make sure the cable is in place before securing the mounting plate
to the surface.
Mounting
plate
7.
Connect the camera drop cable to video and power extension cables.
8.
Reattach the camera to the mounting plate:
a.
Route the camera drop cable through the hole in the mounting surface, if necessary, and then
set the camera module in place on the mounting plate.
Mounting
plate
Camera
module
Housing
Locking
bezel
9.
Connect the far end of the video extension cable to a monitoring device, such as a HD-TVI
compatible setup monitor or HD-TVI DVR.
10.
Connect the far end of the power extension cable to a power supply, then apply power to the
camera through the power extension cable. Observe the voltage polarity shown in the drop cable
photo on page 1.
11.
Rotate the camera module, if necessary, so that the light sensor is at the bottom of the IR array.
12.
While observing video from the camera on a monitor, aim the camera at your surveillance target.
See the figure below for adjustment ranges.
Cleaning
Clean the camera glass with an approved glass cleaning solution and a lint free cloth.
Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
•
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
•
These may cause damage to the surface over time.
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
CAUTION
carefully follow the accompanying instructions.
2
www.observint.com
b.
Place the housing over the camera.
Clips on the mounting plate will hold
the housing and camera in place.
c.
Place locking bezel over the housing,
and onto the mounting plate. Align
the tabs inside the locking bezel with
the slots in the mounting plate, and
then turn the locking bezel about 1/8th
turn clockwise to lock it in secure it to
the plate.
Light
sensor
Troubleshooting
Problem
Nothing appears on the screen
The video image is dim or not clear.
The screen is dark.
The camera is not working properly and the
surface of the camera is hot.
The image on the monitor flickers
Specifications
Camera
ALI-CD1720E
Image Sensor
Progressive Scan CMOS
Effective Pixels
1280(H) * 720(V)
Min. Illumination
0.01 lux @ (F1.2, AGC on), 0 lux with IR
Shutter Time
1/30 s to 1/50,000 s
Lens
3.6 mm Angle of View: 71°
Lens Mount
M12
Angle Adjustment
Pan: 0 ~ 360°, Tilt: 0 ~ 90°, Rotation: 0 ~ 360°
Day & Night
ICR
Synchronization
Internal synchronization
Video Frame Rate
720p @ 30 fps
HD Video Output
1 HD-TVI output
Enclosure color
White
General
Working Temperature/
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity
Humidity 90% or less (non-condensing)
Power Supply
12 Vdc
Power Consumption
Max. 4 W
Weather Proof Ratings
IP66
IR Range
Up to 65 ft (20 m)
Dimension
Φ3.52" × 2.75" (Φ89.5 × 69.8 mm)
Weight
0.57 lb (260 g)
Possible Cause
- Check the power connection.
- Check the video signal cable connection to the monitor.
- If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the contrast control of the monitor.
- Set the monitor impedance properly for the DVR (usually 75 Ω /Hi-Z),
and check the cable connections.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
- Make sure that the camera isn't facing direct sunlight or fluorescent light.
If necessary,change the camera position.
ALI-CD1720G
Progressive Scan CMOS
1280(H) * 720(V)
0.01 lux @ (F1.2, AGC on), 0 lux with IR
1/30 s to 1/50,000 s
2.8 mm; Angle of View: 92˚
M12
Pan: 0 ~ 360°, Tilt: 0 ~ 90°, Rotation: 0 ~ 360°
ICR
Internal synchronization
720p @ 30 fps
1 HD-TVI output
Gray
-40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity 90% or less (non-condensing)
12 Vdc
Max. 4 W
IP66
Up to 65 ft (20 m)
Φ3.52" × 2.75" (Φ89.5 × 69.8 mm)
0.57 lb (260 g)
© 2015 Observint Technologies. All rights reserved.