Makita 3620 Gebrauchsanweisung - Seite 5
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Elektrowerkzeug Makita 3620 herunter. Makita 3620 18 Seiten. Router
Auch für Makita 3620: Gebrauchsanweisung (20 seiten), Gebrauchsanweisung (13 seiten), Gebrauchsanweisung (17 seiten), Gebrauchsanweisung (17 seiten)
Seite drucken
ENGLISH
1
Tighten
2
Loosen
3
Hold
4
Screw
5
Stopper pole
6
Lock lever
7
Depth pointer
8
Adjusting hex bolt
9
Stopper block
SPECIFICATIONS
Model
Collet capacity .............................................8 mm or 3/8"
Plunge capacity ............................................... 0 – 35mm
-1
No load speed (min
) ........................................... 29,000
Overall height ..................................................... 211 mm
Net weight .............................................................. 2.4 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
SPECIFIC SAFETY RULES
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to router safety rules. If you use this tool unsafely or
incorrectly, you can suffer serious personal injury.
1.
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the oper-
ator.
2.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of con-
trol.
3.
Wear hearing protection during extended period
of operation.
4.
Handle the bits very carefully.
5.
Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
6.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
7.
Hold the tool firmly.
8.
Keep hands away from rotating parts.
Explanation of general view
10 Hex nut
11 Switch trigger
12 Feed direction
13 Workpiece
14 Bit revolving direction
15 (View from the top of the tool)
16 Correct bit feed direction
17 Guide bar
18 Straight guide
9.
3620
10. Before using the tool on an actual workpiece, let
11. Be careful of the bit rotating direction and the
12. Do not leave the tool running. Operate the tool
13. Always switch off and wait for the bit to come to
14. Do not touch the bit immediately after operation;
15. Do not smear the tool base carelessly with thin-
16. Draw attention to the need to use cutters of the
17. Some material contains chemicals which may be
GEB018-1
18. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing or removing router bit (Fig.1)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the bit.
Insert the bit all the way into the collet cone and tighten
the collet nut securely with the two wrenches.
A 6 mm or 1/4" collet cone is also provided as standard
equipment besides the 8mm or 3/8" collet cone that is
factory installed on the tool. Use the correct size collet
cone for the bit which you intend to use.
To remove the bit, follow the installation procedure in
reverse.
19 Wing bolt
20 Screw
21 Base plate
22 Templet guide
23 Bit
24 Base
25 Templet
26 Vacuum head
27 Screws
Make sure the bit is not contacting the work-
piece before the switch is turned on.
it run for a while.
Watch for vibration or wobbling that could indi-
cate improperly installed bit.
feed direction.
only when hand-held.
a complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your
skin.
ner, gasoline, oil or the like.
They may cause cracks in the tool base.
correct shank diameter and which are suitable
for the speed of the tool.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
the material and application you are working
with.
5