Makita 5143R Gebrauchsanweisung - Seite 9
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Elektrowerkzeug Makita 5143R herunter. Makita 5143R 12 Seiten. Circular saw
Auch für Makita 5143R: Gebrauchsanweisung (13 seiten), Gebrauchsanweisung (13 seiten), Gebrauchsanweisung (13 seiten), Gebrauchsanweisung (16 seiten), Gebrauchsanweisung (13 seiten)
Seite drucken
saw blade.
CAUTION:
Ensure that the riving knife is adjusted such that:
•
The distance between the riving knife and the
toothed rim of the saw blade is not more than 5 mm.
The toothed rim does not extend more than 5 mm
beyond the lower edge of the riving knife.
Switch action
005398
CAUTION:
Before plugging in the tool, always check to see
•
that the switch trigger actuates properly and returns
to the "OFF" position when released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
push in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
•
unplugged before carrying out any work on the tool.
4.
Removing or installing saw blade
The following blade can be used with this tool.
Model
Max. dia.
Min. dia.
5603R
165 mm
150 mm
190 mm
170 mm
5703R,5705R
5903R
235 mm
210 mm
5103R
270 mm
260 mm
5143R
355 mm
350 mm
006481
The thickness of the riving knife is 1.8 mm for Models
5603R,5703R and 5705R or 2.0 mm for Models for
5903R and 5103R or 2.5 mm for Model 5143R.
CAUTION:
Do not use saw blades which do not comply with
•
the characteristics specified in these instructions.
Do not use saw blades the disc of which is thicker
•
or the set of which is smaller than the thickness of
the riving knife.
1. Lock-off button
2. Switch trigger
1
2
Blade thickness
Kerf
1.6 mm or less
1.9 mm or more
1.6 mm or less
1.9 mm or more
1.7 mm or less
2.1 mm or more
1.8 mm or less
2.2 mm or more
2.3 mm or less
2.7 mm or more
1
005399
CAUTION:
Be sure the blade is installed with teeth pointing up
•
at the front of the tool.
Use only the Makita wrench to install or remove the
•
blade.
Never depress the shaft lock while the saw is
•
running.
To remove the blade, press the shaft lock fully so that the
blade cannot revolve and use the hex wrench to loosen
the hex bolt counterclockwise. Then remove the hex bolt,
outer flange and blade.
To install the blade, follow the removal procedure in
reverse. BE SURE TO TIGHTEN THE HEX BOLT
CLOCKWISE SECURELY.
3
2
1
005400
When changing blade, make sure to also clean upper
and lower blade guards of accumulated sawdust. Such
efforts do not, however, replace the need to check lower
guard operation before each use.
Connecting a vacuum cleaner
1
005414
When you wish to perform clean cutting operation,
connect a Makita vacuum cleaner to your tool. Install the
joint on the tool using the screws. Then connect a hose of
the vacuum cleaner to the joint as shown in the figure.
9
1. Hex wrench
2. Shaft lock
2
1. Hex socket head
bolt
2. Outer flange
3. Saw blade
Inner flange
4
1. Vacuum cleaner