KitchenAid 9752397 Installationsanleitung Handbuch - Seite 5
Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Ranges KitchenAid 9752397 herunter. KitchenAid 9752397 7 Seiten. 30" (76.2 cm) sealed burner gas freestanding and slide-in ranges, with self-cleaning thermal/convection oven
Seite drucken
Now start...
25"
J63.5 cm)
countertop
over 24"
!"ab Z2
Press on front of
With range in kitchen.
(II
Put on safety glasses and gloves.
.
Remove shipping materials, tape and
protective film from range. Keep
cardboard bottom and shipping base under range.
Remove oven racks and parts package from inside
oven. If you have a slide-in
range, remove back
vent package from range top. See Step 7 for
installation.
open. Pull open to first stop
position. Lift front of drawer to
clear white wheels in drawer
Y
I/
guides. Remove drawer and set it aside on a
protected surface.
template
(141
Carefully move
.
range into final
position. Look under
range (a flashlight may be
needed) to check that left rear
leveling leg is engaged in the
anti-tip bracket. If leveling leg is
not properly engaged, remove ar
anti-tip bracket to insure that the
properly in the anti-tip bracket.
PI
Place the anti-tip bracket template on the
'
floor in the cabinet opening so that the left
edge is against cabinet and the top edge
is against the rear wall, molding or cabinet. If
countertop
is deeper than 25 inches (63.5 cm),
measure and mark a distance 25 inches (63.5 cm) in
from front of countertop
opening
and align
template with mark (or subtract 2.5 inches (63.5 cm)
from the countertop depth and add the difference to
the corresponding
dimension).
ld reposition the
leveling leg fits
21
Take 4 cardboard corner posts from the
.
carton. Stack one cardboard corner post
on top of another. Repeat with the other
two corner posts. Place corner posts lengthwise
on
the floor in back of range so corner posts will
support outer side edges of range as shown.
1151
Place rack in
oven. Place
.
level on rack,
first side to side; then front
to back. If the range is not
level, DUII ranae forward
A = Difference
between
until the rear hveling
leg
'
'
is removed from the anti-tip bracket. Adjust the
leveling legs up or down. Then slide range back
into position. Check that leveling leg is engaged in
anti-tip bracket.
NOTE: Oven must be level for satisfactory
baking
conditions.
Excessive
Weight Hazard
Use two or more people to move and install
range.
Failure to follow
this instruction
can result
in back or other injury.
l-3-l
Firmly grasp the range and gently lay it on
.
its back on the cardboard corner posts.
All connections
must be wrench-tightened.
Pull cardboard bottom and shipping base
firmly to remove.
pressure
regulator
and valve assembly
flexible
connector
manual
I
shutoff
valve
If countertop
is not flush to the side of the cabinet
opening, align the left side of the template to allow
for the countertop overhang. Tape the freestanding
range anti-tip bracket template in place.
El
Use an adjustable
.
wrench to loosen th
leveling legs l-1/2 t
Place cardboard or hardboard in front of
range. Stand range back up onto
cardboard or hardboard.
Contact
a qualified
floor covering
installer
for
the best procedure
of drilling
mounting
holes
through
your type floor covering.
Before moving,
slide range onto cardboard
or
hardboard.
112" (1.3 c-m) flare union adapters
ml
Assemble the flexible connector from
n
the gas supply pipe to the pressure
regulator, located in the lower left side
of the storage drawer area, in this order: shutoff
valve, l/2" (1.3 cm) flare union adapter, flexible
connector, l/2" (1.3 cm) flare union adapter. Seal
all openings in floor or wall wherever range is
installed.
110)
To mount anti-
tip bracket to
n
wood floor,
use the anti-tip bracket
template to mark where to
drill mounting holes. Use a
drill with a l/B" (0.3 cm)
drill bit to drill the two
mounting holes. Remove
template from floor.
To mount anti-tip
bracket
to concrete
or ceramic floor, use the anti-tip
bracket template to mark where to drill mounting
holes. Use a drill with a 3/16" (0.5 cm) masonry
drill bit to drill the two holes. Remove template from
floor. Tap plastic anchors into mounting holes in
floor with hammer.
remove the outside
v
v
screws from rear trim on
range. Use screws to attach back vent to range.
(81
Check that the type of gas supply is
correct for this range. (See model/serial
n
rating plate.)
If connecting
to L.P. Gas, follow directions in
Conversion
Kit included in your literature package.
If connecting
to Natural gas, go to Step 9.
Use pipe-joint compounds
appropriate
for use with L.P. gas to seal all gas
connections.
If flexible connectors
are
used. be certain connectors
are not kinked.
(181
Open the shutoff valve in the gas
.
supply line. Wait a few minutes
for the gas to move through
the gas line.
m
Use a brush and liquid detergent to test
all gas connections
for leaks. Bubbles
around gas connections
will indicate a
leak. If a leak appears, shut off gas valve controls
and adjust connections.
Then check connections
again. NEVER TEST FOR GAS LEAKS WITH A
MATCH OR OTHER FLAME. Clean all detergent
solution from range.
ml
Line up holes in
anti-tip bracket with
'
mounting holes in
floor. Use the screws provided
to fasten anti-tip bracket to
floor.
NOTE: Anti-tip
bracket must
be mounted
securely
to the
sub-floor.
Depending on the
thickness of your flooring, longer screws may be
necessary to anchor the bracket to the sub-floor.
Longer screws are available from your local
hardware store.
Tip Over Hazard
Connect
anti-tip
bracket to the range.
Reconnect
anti-tip
bracket, if the range is
moved.
Do not push down on the open oven door.
Follow the installation
instructions.
Do not let children
climb onto the oven door.
Failure to follow
these instructions
can
result in death. burns or other iniurv.
1121
Move range close to cabinet opening.
.
Remove cardboard or hardboard from
under range.
Panel D