KitchenAid 9752913 Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Ranges KitchenAid 9752913 herunter. KitchenAid 9752913 5 Seiten. 30"

Seite drucken

Your safetv and the safetv

of others

is' very importank

We have provided many important safety

messages in this manual and on your

appliance. Always read and obey all safety

messages.

q !

This is the safety alert symbol. This

symbol alerts you to hazards that can

kill or hurt you and others. All safety

messages will be preceded by the safety alert

symbol and the word "DANGER" or

"WARNING". These words mean:

36" (91.4 c'm)

cooktop

height with

leveling

legs

lowered

l-1/2 turns

12-l 12"

(57.1 cm)

You &l

be killed or seriously

injured

you don't follow

instructions.

You can be killed or seriously

injured

you don't follow

instructions.

All safety messages will identify the hazard,

tell you how to reduce the chance of injury,

and tell you what can happen if the

instructions

are not followed.

(2.5 cm)

Important:

Observe all governing

codes and

ordinances.

Failure to meet codes and

ordinances

could lead to fire or electrical

shock.

Proper installation

is your responsibility.

qualified technician

must install this range. Make

sure you have everything

necessary for correct

installation.

It is the installer's

responsibility

comply with installation

clearances specified on

the model/serial

rating plate. The model/serial

rating plate is located on the oven frame behind

the storage drawer panel.

Check location where range will be installed.

The range should be located for convenient

use

in kitchen.

When installing

a range under existing cabinets

and the installation

does not meet the minimum

cabinet clearances, install a range hood above

the cooktop to avoid burn hazards.

ALL OPENINGS IN THE WALL OR FLOOR

WHERE RANGE IS TO BE INSTALLED MUST

BE SEALED.

Cabinet opening dimensions

that are shown

must be used. Given dimensions

are minimum

clearances.

Grounded electrical

supply is required. See

"Electrical

requirements,"

Panel B.

It is the customer's

responsibility:

To contact a qualified

electrical installer.

To assure that the electrical installation

adequate and in conformance

with National

Electrical Code, ANSVNFPA 70 - latest edition*

and all local codes and ordinances.

Mobile home installation

The installation

of this range must conform with

the Manufactured

Home Construction

and

Safety Standard, Title 24 CFR, Part 3280

[formerly

the Federal Standard for Mobile Home

Construction

and Safety, Title 24, HUD (Part

28011 or, when such standard is not applicable,

the Standard for Manufactured

Home

Installations,

ANSI A225.1/NFPA 501A*, or with

local codes.

When this range is installed

in a mobile home, it

must be secured to the floor during transit. Any

method of securing the range is adequate as

long as it conforms to the standards listed

above.

Four-wire power supply cdrd or cable must be

used in a mobile home installation.

The

appliance wiring will need to be revised. See

"Four-wire

electrical connection,"

Panel B.

Copies of the standards

listed may be obtained

from:

* National

Fire Protection

Association

Batterymarch

Park

Quincy, Massachusetts

02269

--"

(76.2 cm) min.

25" (63.5 cm) countertop

depth

24" (61 cm) base cabinet

depth

36" (91.4 cm) countertop

height

When installed

in a 24" (61 cml base

cabinet

with 25" (63.5 cm)

countertop

front of oven door

protrudes

l-7/8"

(4.8 cm) beyond

24" (61 cm) base cabinet.

Note: 24" (61 cm) min. when bottom

of wood

or metal cabinet

protected

by not less than 114"

(0.64 cm) flame retardant

millboard

covered

with

not less than No. 28

MSG sheet steel, 0.015" (0.4 mm)

stainless

steel, 0.024" (0.6 mm)

aluminum

or 0.020" (0.5 mm)

copper.

30" (76.2 cm) min. clearance

between

the top of the cooking

platform

and the bottom

of an

unprotected

wood

or metal cabinet.

30-3/8"

(77.2 cm)

l *

min. clearance

from both sides

of range to side

wall or other

combustible

material

between

upper

cabinet

and

8" (20.3 cm) to

22" (55.9 cm) from

either cabinet,

7" (17.8 cm) max.

Do not

seal range

to side

cabinets.

between

cutout

The floor-mounted

anti-tip

bracket

MUST be installed.

To install

the

anti-tip

bracket

shipped

with the

range, see Panel C and the anti-tip

bracket

template/instruction

sheet.

The cook-top sides of the slide-in range fit over

the cutout edge of your countertop.

If you have a square finish (flat) countertop

and

the opening width is 30-3/B" (77.2 cm), no

countertop

preparation

is required.

Formed front-edged

countertops:

Must have

molded edge shaved flat l/4" (0.64 cm) from

each front corner of opening.

Tile countertops

may need trim cut back

l/4" (0.64 cm) from each front corner and/or

rounded edge flattened.

If countertop

opening width

is greater than

30-3/8" (77.2 cm), adjust the l/4" (0.64 cm)

dimension.

Countertop

must be level. Place level on

countertop,

first side to side; then front to back.

If countertop

is not level, range will not be level.

Oven must be level for satisfactory

baking

conditions.

/ -..

/ ' s 4

114'

(0.64 cml

Cooktop

sides of range fit over

edges of countertop

opening.

wood floors:

l/8"

drill bit

concrete/ceramic

floors:

3/16" carbide-tipped

masonry

drill bit (Hammer

may be needed for

anchors.)

2 plastic

anchors

2 screws

(#IO x l-1/2")

floor-mounted

Not shown:

anti-tip

bracket

literature

pack

Brackets

must be securely

mounted

to sub-floor.

Thickness

of flooring

may require

longer

screws to

anchor bracket

to sub-floor.

Longer screws

are

available

from your local hardware

store.

tape or ruler

Panel A

/ 6F

safety

-'v :,

. .

glasses

gloves

channel

lock