ALIBI ALI-NS2036R Handbuch zur Schnellinstallation - Seite 3

Blättern Sie online oder laden Sie pdf Handbuch zur Schnellinstallation für IP-Kamera ALIBI ALI-NS2036R herunter. ALIBI ALI-NS2036R 9 Seiten. 6mp starlight ip turret camera

Seite drucken

ALIBI ALI-NS2036R Handbuch zur Schnellinstallation

Adjust the turret and shroud assembly so that the "UP" mark on the turret is up.

Apply power to the camera through the 12 Vdc power cable or PoE injector, as configured.

Step 5.

Install the Alibi Config Tool software

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.

The Alibi Config Tool is a PC-based network utility for discovery of Alibi compatible devices. It provides

an easy way to activate devices, configure camera and recorder network configuration settings, and set

device passwords. It can be installed on a Microsoft® Windows® operating system that has direct access

to the network where your Alibi devices are installed. You can download the Alibi Configuration Tool

from AlibiSecurity.com/Resources.

Download the Alibi Config Tool from the AlibiSecurity.com/Resources website. At the time

when this document was published, the file is named: alibi-config-tool.zip and is about 80MB.

Un-zip the file on a computer with Microsoft Windows (Windows 7 or newer) that is connected

to the LAN where your Alibi camera is connected.

Run the file contained in the zip file: Alibi Config Tool.exe. Follow the on-screen instructions

to install the file.

Open the Alibi Config Tool application. When the application opens, it automatically "discovers"

and lists all Alibi compatible devices on the LAN. See below.

Note: In the screen above, the tool can discover devices on other subnetworks. It will also list

other Alibi compatible devices on the LAN, and devices with the address 192.168.1.64 (an

inactive Alibi device).

Step 6.

Activate Inactive Alibi device

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this step.

Refer to the documentation available for your NVR firmware for the procedure to activate the camera, if

necessary.

When an Alibi device is first installed, or reset to its factory configuration, it must be "Activated" before

it can be used. In the Alibi Configuration Tool, "Inactive" devices have a Security status of Inactive,

and an IPv4 address of 192.168.1.64. A device is "Activated" when a password is assigned to the

admin username of the device.

In the example below, an ALI-NS2036R camera is activated and configured for its network. The

procedure is similar for all other Alibi network cameras currently available.

Scan through the list of devices the Alibi Config Tool discovered for the Inactive device you want

to activate (see below). Click on the device in the list to highlight it, and then click the select box

to check it. See below.

www.observint.com

Selected

Activate

Click the Activate button. In the Activate window, you will create a password for the admin

(administrator) username.

In the Activate window, enter an a password for admin in the New Password field.

Include a combination of uppercase, lowercase alphabetic characters and numbers to

create a "Strong" password. The rating is shown beneath the Password field. See above.

Enter the admin password again in the Confirm field, and then click Activate. In the

screen below, notice that the device Security status shows "Active". Record your admin

password for reference later.

If you lose your admin (administrator) password, you cannot configure the device or restore



it to its factory settings. To reset your password, call your support organization for specific

CAUTION

instructions.

Notice that although the device is now activated, it retained the default IP address.

Step 7.

Edit Network Parameters

NOTE: If the camera LAN extension cable is attached to a Network Video Recorder (NVR), skip this

step. The camera will receive network configuration settings from the NVR. Refer to the documentation

available for your NVR firmware for more information.

You can change the network parameters of devices that are active.

In the list of devices discovered, click on the device you want to change the network settings for,

and then click the select box to check it. See below.

Edit Network Parameters

In the popup window, edit the current network parameters, and then enter the Administrator

(admin) user password in the field at the bottom.

Enable DHCP: You can select Enable DHCP to acquire compatible network settings

from a DHCP server installed on the LAN. However, these settings might be changed later

by the DHCP server. Since it is recommended to use an unchanging IP address, you can

use Edit Network Parameters with DHCP to acquire compatible network settings, and

then use Edit Network Parameters again to uncheck Enable DHCP and save that

configuration to retain the fixed network parameters.

In the example below, Enable DHCP was checked to acquire compatible network

settings from the DHCP server.