Makita BJV180 Gebrauchsanweisung - Seite 8

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Elektrowerkzeug Makita BJV180 herunter. Makita BJV180 18 Seiten. Cordless jig saw
Auch für Makita BJV180: Aufschlüsselung der Teile (3 seiten), Spezifikationsblatt (2 seiten), Gebrauchsanweisung (13 seiten), Gebrauchsanweisung (13 seiten), Gebrauchsanweisung (13 seiten), Technische Informationen (13 seiten)

Seite drucken

Selecting the cutting action (Fig. 3)

This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action

thrusts the blade forward on the cutting stroke and greatly increases cutting speed.

To change the cutting action, just turn the cutting action changing lever to the desired cutting action position.

Refer to the table to select the appropriate cutting action.

Position

Straight line cutting action

Small orbit cutting action

Medium orbit cutting action

Large orbit cutting action

III

006376

Switch action (Fig. 4 & 5)

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the "OFF" position when

released.

• When not operating the tool, depress the lock-off but-

ton from A side to lock the switch trigger in the OFF

position.

To prevent the switch trigger from accidentally pulled, the

lock-off button is provided.

To start the tool, depress the lock-off button from B side

and pull the switch trigger.

Tool speed is increased by increasing pressure on the

switch trigger. Release the switch trigger to stop. After

use, always press in the lock-off button from A side.

Lighting up the lamps

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger

to turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing saw blade

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade and/or blade holder. Failure to do so may

cause insufficient tightening of the blade, resulting in a

serious injury.

• Do not touch the blade or the workpiece immediately

after operation; they may be extremely hot and could

burn your skin.

• Tighten the saw blade securely. Failure to do so may

cause a serious injury.

Cutting action

Applications

For cutting mild steel, stainless steel and plastics.

For clean cuts in wood and plywood.

For cutting mild steel, aluminum and hard wood.

For cutting wood and plywood.

For fast cutting in aluminum and mild steel.

For fast cutting in wood and plywood.

• When you remove the saw blade, be careful not to hurt

your fingers with the top of the blade or the tips of work-

piece.

To install the blade, open the tool opener to the position

shown in the figure. (Fig. 6)

Keeping that situation, insert the saw blade into the blade

clamp as far as the two protrusions of the blade can not

be seen. (Fig. 7)

Return the tool opener to its original position.

After installing, always make sure that the blade is

securely held in place by trying to pull it out.

CAUTION:

• Do not open the tool opener excessively, or it may

cause tool damage.

To remove the blade, open the tool opener to the position

shown in the figure. (Fig. 8) Pull the saw blade out

toward the base.

NOTE:

• Occasionally lubricate the roller.

Hex wrench storage (Fig. 9)

When not in use, store the hex wrench as shown in the

figure to keep it from being lost.

Cover plate (Fig. 10)

Use the cover plate when cutting decorative veneers,

plastics, etc. It protects sensitive or delicate surfaces

from damage. Fit it on the back of the tool base.

Anti-splintering device (Fig. 11)

For splinter-free cuts, the anti-splintering device can be

used. To install the anti-splintering device, move the tool

base all the way forward and fit it from the back of tool

base. When you use the cover plate, install the anti-splin-

tering device onto the cover plate.

CAUTION:

• The anti-splintering device cannot be used when mak-

ing bevel cuts.

Dust extraction

The dust nozzle (optional accessory) is recommended to

perform clean cutting operations. (Fig. 12)

To attach the dust nozzle on the tool, insert the hook of

dust nozzle into the hole in the base.

The dust nozzle can be installed on either left or right

side of the base. (Fig. 13)