ALIBI ALI-NS1132VR Handbuch zur Schnellinstallation - Seite 7
Blättern Sie online oder laden Sie pdf Handbuch zur Schnellinstallation für Digitalkamera ALIBI ALI-NS1132VR herunter. ALIBI ALI-NS1132VR 7 Seiten. 2mp ip dome camera
Seite drucken
General
-22 °F ~ 122 °F (-30 °C ~ 50 °C),
Operating Conditions
Humidity: 95% or less (non-condensing)
12 Vdc ± 25%, 5.5 mm coaxial power plug
Power Supply
PoE (802.3af, class 3)
Power Consumption and
12 Vdc, 0.8 A, Max: 10 W;
Current
PoE: (802.3af, 37 V ~ 57 V), 0.35 A ~ 0.2 A, Max: 12 W
Protection Level
IP67, IK10, TVS 2000V lightning protection, surge protection and voltage transient protection
Material
Metal and plastic
Camera: 5.6" × 3.9" (Φ 141 mm × 99.9 mm)
Dimensions
Camera with packaging: 5.5" × 5.5" × 6.1" (140 mm × 140 mm × 154 mm)
Camera: 1.8 lb (830 g) approx.
Weight
Camera with packaging: 2.4 lb (1070 g) approx.
TVS 2000V lightning protection, surge protection and voltage transient protection
This product includes TVS plate lightning protection technology to prevent damage caused by a pulse
signal that is below 3000 watts from sources such as lighting, surging, etc. Protection measures must be
taken to ensure electrical safety.
The distance between signal transmission line and high-voltage equipment or high-voltage cable is
•
at least 165 ft (50 m).
Outdoor wiring should better be along the eaves as much as possible.
•
In the open field, wiring should be buried underground in sealed steel pipe with one-point
•
grounding. Overhead routing method is not acceptable.
In regions with thunderstorms or where high induction voltage are present (such as high-voltage
•
transformer substation), high power lightning protection apparatus and lightning conductor are
necessary.
The design for installation and wiring with lightning protection and grounding should be combined
•
with the lightning protection consideration of the building, and conform to the relevant national
and industry standards.
The system should ensure equipotential grounding. Grounding equipment must satisfy both system
•
anti-jamming and electric safety. It must not allow short circuit and open circuit with the zero
conductor of strong grid. When the system is singularly ground, the resistance must less than
4 Ω and the cross-sectional area of the grounding cable must be no less than 25 mm
instructions, refer to local electrical codes.
Video arrester
Com. arrester
Power arrester
The resistance of
earthing conductor
must be less than 4 Ω.
Steel jacket
www.observint.com
7
. For grounding
2
Lightening rod
45° conical
envelope
The camera should be
within a 45° envelope
under the lightening rod.
Using the Waterproof Ethernet Fitting
Install the Waterproof Ethernet Fitting on the Ethernet cable end at the camera when moisture or
contamination exists in the area near the camera. The fitting includes several parts that must be installed in
a specific order. To install the fitting:
1.
Place the rubber O-ring over the camera drop cable end cap.
Push the O-ring up to the connector cap.
2.
Place the Lock Nut onto the network cable from the router
or switch as shown in the drawing to the right. The inside
threads must be toward the camera end.
3.
Place the rubber basket onto the network cable above the lock
nut as shown.
4.
Place the end cap onto the network cable above the rubber
gasket as shown. The fingered end must be toward the router
or switch.
5.
Install an RJ-45 connector onto the network cable.
6.
Plug the RJ-45 connector with the network cable into the
camera network drop cable.
7.
Fit the end cap on the network cable onto the camera drop
cable end cap. Rotate the network cable end cap to lock it in
place.
8.
Push the rubber gasket fully into the end of the network cable
end cap.
9.
Screw the lock nut onto the network cable end cap until it is
fully seated.
Network drop cable
from camera
Ethernet Fitting installed
Ethernet Fitting assembled and connected
Network drop
cable from
camera
Drop cable
end cap
Rubber
O-ring
seal
RJ-45
connector
End cap
Rubber
gasket
Network cable from
router or switch
Lock nut
Network
cable
from
router or
switch
© 2019 Observint Technologies. All rights reserved.