Makita DCO180 Gebrauchsanweisung - Seite 2
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Elektrowerkzeug Makita DCO180 herunter. Makita DCO180 13 Seiten. Cordless cut-out tool
Auch für Makita DCO180: Gebrauchsanweisung (13 seiten), Technische Informationen (8 seiten)
Seite drucken
SPECIFICATIONS
Collet chuck capacity
Rated speed (n)/ No load speed (n
Overall length
Rated voltage
•
Due to our continuing program of research and development, the specifications herein are subject to change without notice.
•
Specifications may differ from country to country.
•
The weight may differ depending on the attachment(s), including the battery cartridge. The lightest and heavi-
est combination, according to EPTA-Procedure 01/2014, are shown in the table.
Applicable battery cartridge and charger
Battery cartridge
Charger
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Only for EU countries
Ni-MH
Due to the presence of hazardous com-
Li-ion
ponents in the equipment, waste electrical
and electronic equipment, accumulators
and batteries may have a negative impact
on the environment and human health.
Do not dispose of electrical and electronic
appliances or batteries with household
waste!
In accordance with the European Directive
on waste electrical and electronic equip-
ment and on accumulators and batteries
and waste accumulators and batteries,
as well as their adaptation to national law,
waste electrical equipment, batteries and
accumulators should be stored separately
and delivered to a separate collection point
for municipal waste, operating in accor-
dance with the regulations on environmen-
tal protection.
This is indicated by the symbol of the
crossed-out wheeled bin placed on the
equipment.
Intended use
The tool is intended for cutting gypsum, wood, plastic
and soft wall tiles.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-17:
Sound pressure level (L
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model
)
0
Net weight
D.C.14.4 V Model
D.C.18 V Model
) : 77 dB (A)
pA
DCO140
3 mm, 6 mm or 1/8", 1/4"
-1
30,000 min
313 mm
1.6 kg
D.C. 14.4 V
BL1415N / BL1430B / BL1440 / BL1460B
BL1815N / BL1820B / BL1830B / BL1840B / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF /
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the tool is
used especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-17:
Work mode : rotation without load
Vibration emission (a
Uncertainty (K) : 1.5 m/s
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
2 ENGLISH
DCO180
3 mm, 6 mm or 1/8", 1/4"
-1
30,000 min
313 mm
1.5 - 1.8 kg
D.C. 18 V
DC18SH
2
) : 2.5 m/s
or less
h
2