Lexmark 09H0052 - T522 25PPM LASERPR Kurzreferenz - Seite 2

Blättern Sie online oder laden Sie pdf Kurzreferenz für Drucker Lexmark 09H0052 - T522 25PPM LASERPR herunter. Lexmark 09H0052 - T522 25PPM LASERPR 2 Seiten. Lexmark optra t522: quick reference

Seite drucken

Operator panel menus

Paper Menu

Finishing Menu

Utilities Menu

Paper Source

Duplex

Print Menus

Paper Size

Duplex Bind

Print Net <x> Setup

Paper Type

Copies

Print Fonts

Custom Types

Blank Pages

Print Directory

Universal Setup

Collation

Factory Defaults

Substitute Size

Separator Sheets

Format Flash

Configure MP

Separator Source

Defragment Flash

Envelope Enhance

Multipage Print

Format Disk

Paper Texture

Multipage Order

Job Acct Stat

Paper Weight

Multipage View

Hex Trace

Paper Loading

Multipage Border

PostScript Menu

Serial Menu

Parallel Menu

PCL SmartSwitch

Print PS Error

PCL SmartSwitch

Font Priority

PS SmartSwitch

NPA Mode

Serial Buffer

Parallel Buffer

Job Buffering

RS-232/RS-422

Advanced Status

RS-422 Polarity

Protocol

Serial Protocol

Honor Init

Robust XON

Parallel Mode 1

Baud

Parallel Mode 2

Data Bits

Parity

Honor DSR

Network Menu

Infrared Menu

USB Menu

PCL SmartSwitch

Infrared Port

PCL SmartSwitch

PS SmartSwitch

PCL SmartSwitch

PS SmartSwitch

NPA Mode

PS SmartSwitch

NPA Mode

Network Buffer

NPA Mode

USB Buffer

Job Buffering

Infrared Buffer

Job Buffering

Network <x> Setup

Job Buffering

Mac Binary PS

Window Size

Transmit Delay

Max Baud Rate

Accessing paper jam areas

You open doors and covers, remove paper trays, and remove options to access paper jam areas. If your

Job Menu

Quality Menu

printer has a multipurpose feeder, it is visible when the lower front door is opened. The illustration shows the

Confidential Job

Print Resolution

Held Jobs

location of paper sources and possible paper jam areas.

Toner Darkness

Cancel Job

PQET

Reset Printer

PictureGrade

Print Buffer

202 Paper Jam

Printer rear door

230 Paper Jam

Duplex rear door

250 Paper Jam

Lower front door

(down when envelope

PCL Emul Menu

Setup Menu

Font Source

feeder is installed)

Printer Language

Font Name

Power Saver

Point Size

Resource Save

Pitch

Download Target

Symbol Set

Print Timeout

Orientation

Wait Timeout

Lines per Page

Auto Continue

24x Paper Jam

A4 Width

Jam Recovery

Tray Renumber

Page Protect

Integrated input tray

Auto CR after LF

Display Language

Auto LF after CR

Alarm Control

Toner Alarm

Job Accounting

Warning:

Do not attempt to clear any paper jam using tools or instruments. This may permanently

damage the printer.

LocalTalk Menu

LocalTalk Port

PCL SmartSwitch

PS SmartSwitch

NPA Mode

LocalTalk Buffer

Job Buffering

NPA Hosts

LocalTalk Name

LocalTalk Addr

LocalTalk Zone

Print quality problems

Problem

Print is too light.

200 Paper Jam

201 Paper Jam

Upper front door

260 Paper Jam

Envelope feeder

Toner fog or background shading

appears on the page.

230 Paper Jam

Duplex front

access cover

Streaks appear on the page.

24x Paper Jam

Paper trays

The job prints, but the top and side

margins are incorrect.

Action

• The toner may be low. To utilize the remaining toner, remove the

cartridge by gripping the handles with both hands. With the cartridge

arrows pointing downward, shake the print cartridge back and forth.

Reinstall the cartridge and then press Go.

• Change the Toner Darkness setting in the Quality Menu.

• If you are printing on an uneven print surface, change the Paper

Weight and Paper Texture settings in the Paper Menu.

Verify that the correct print material is being used.

• Check the print cartridge to make sure it is installed correctly.

• Change the print cartridge.

• If the problem continues, change the charge roll.

• The toner may be low. To utilize the remaining toner, remove the

cartridge by gripping the handles with both hands, and then shake the

print cartridge vigorously. Reinstall the same print cartridge.

• If you are using preprinted forms, make sure the ink can withstand

temperatures of 212°C (414°F).

• Make sure the Paper Size setting in the Paper Menu is correct.

• Make sure the margins are set correctly in your software application.