Lexmark 21S0732 - E323N 20PPM LASERPR Kurzreferenz-Handbuch
Blättern Sie online oder laden Sie pdf Kurzreferenz-Handbuch für Drucker Lexmark 21S0732 - E323N 20PPM LASERPR herunter. Lexmark 21S0732 - E323N 20PPM LASERPR 2 Seiten. Lexmark e321: quick reference
Seite drucken
Quick Reference
Loading tray 1
1
Extend the rear paper support until you hear a click.
2
Straighten the edges on a level surface. Flex the sheets back
and forth to loosen them, fan the sheets on all four sides, and
flex them again.
Note:
Not flexing and fanning the media may cause feed problems
and jams.
3
Load:
•
letterhead paper with the top of the page pointing down, facing
you.
•
envelopes in the center of the tray.
Load them vertically, flap side down, with the stamp area in
the top left corner.
4
Extend the front paper support on the top output bin.
5
Slide the paper guides flush against the edges of the media.
6
Open the front output door if you are printing on special media.
7
Choose the paper size and type from your software
application.
8
Start your print job.
Loading the optional 250-sheet
tray
Grasp the tabs on either side of the paper tray and pull it completely
out of the printer.
1
If loading:
•
letterhead paper, insert letterhead face down with the top of
the page entering the printer first.
•
A4 or legal size paper, extend the paper support.
2
Make sure the metal plate is pressed down before inserting the
paper tray into the printer.
Note:
After the paper tray is inserted, the metal plate springs back
up so the paper can feed into the printer.
3
Do not exceed the stack height indicator; overfilling the tray
may cause jams.
4
Slide the paper guides against the edges of the paper.
5
Make sure the paper is under both corner bucklers and is flat
in the tray.
Corner
Stack height
bucklers
indicator
6
Reinstall the tray, making sure the tray is pushed all the way in.
7
Select the paper size and type from your software application.
8
Start your print job.
Clearing jams
The Paper Jam light prompts you to clear the paper path.
1
Open the printer cover.
2
Remove the print cartridge (it may be warm) and cover it.
Warning!
Exposing the photoconductor to light may
damage the print cartridge.
Photoconductor
3
Gently pull out the media.
Fuser
Roller
CAUTION!
The fuser may be hot!
4
If the media is jammed tightly behind the roller, or if you cannot
get a grip on it, close the cover, open the front output door, and
pull out the paper.
5
Make sure there is no more media in the printer.
6
Reinstall the print cartridge.
7
Close the printer cover to resume printing.
8
Press
Continue
to clear the message.
If the jam occurs as it exits the optional 250-sheet tray into the
printer:
1
Open the printer cover.
2
Remove the print cartridge (the print cartridge may be warm).
3
Gently pull the paper toward you.
4
Reinstall the print cartridge.
5
Close the printer cover to resume printing.
6
Press
Continue
to clear the message.
If you cannot reach the paper easily:
1
Turn off the printer. (You will lose the rest of the print job.)
2
Lift the printer off the drawer.
3
Remove the paper.
4
Reinstall the drawer.
5
Turn on the printer.
6
Resend your print job.
If the jam occurs just after the paper feeds from the optional 250-
sheet tray:
1
Pull the tray all the way out.
2
Gently pull the paper toward you.
3
Reinstall the tray to resume printing.
4
Press
Continue
to clear the message.