Garden Oasis FD0133BA Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Außen-Brunnen Garden Oasis FD0133BA herunter. Garden Oasis FD0133BA 3 Seiten. Lion wall fountain

Seite drucken

Unpack the contents of the box and make sure that all items are accounted for and in good condition.

2. 2. 2. 2.

Select a flat, level surface for the assembly. Place the fountain top onto the basin making sure to align and insert the posts on the underside of the

fountain top into the post holes on top of the basin. Align the bolt holes at the back of the fountain top to the bolt holes on the basin top. Insert a bolt and

washer into each bolt hole and use a wrench to tighten the bolt in order to secure the fountain top to the basin. Place the pump upright in the basin and

draw the pump power cord out from the cord slot on the underside of the basin. Insert the water supply tube into the pump outlet on top of the pump. Place

the pump cover into the basin and over the pump to conceal it. (Fig.1& 2)

Add clean water into the basin. The water level should be approximately 0.8 in. / 20 mm below the edge of the basin. (Fig.2)

Connect the pump power cord to a GFCI outlet and the product will begin to function as intended

To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing after the initial setup of your fountain. It is

highly recommended that this fountain be placed in an area that cannot be damaged by water.

Do not leave your fountain running for extended periods of time when no one is present to observe the performance.

Check the area around your fountain on a regular basis to ensure that there is no leakage.

CAUTIONS:

The pump has been evaluated for use with water only.

•

Risk of electric shock.

•

Do not remove cord and strain relief. Do not connect conduit to pump.

•

Do not use the pump in water exceeding 86ºF / 30ºC.

•

Do not use the pump in flammable liquids.

•

Do not use the pump for industrial purposes.

Do not use the pump in vehicles or on board ships or aircraft or swimming pools.

•

Do not use the pump in location where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapor or gas).

•

Do not let the pump run dry. Pump must be completely submerged for proper operation and cooling.

•

Do not lift the pump by its power cord.

•

Keep the plug dry. Do not expose the plug to water or steam.

•

Before connecting to the power source, make sure that the pump is assembled and completely submerged in water.

•

Always disconnect the pump from the power source before performing any maintenance on the pump, lights (if equipped), or fountain.

•

Do not exceed the voltage shown on the pump.

•

Check the water level regularly to ensure the pump is completely submerged during operation. The pump should be fully submerged during operation.

Do not add water while operating the product. Always disconnect the pump from the power source before adding water.

WARNINGS:

Risk of electric shock. This pump is supplied with a grounding conductor and grounding-type attachment plug. To reduce the risk of electric shock, be

certain that it is connected only to a properly grounded, grounding-type receptacle.

To reduce the risk of electric shock, use only on portable self-contained fountains no larger than 5 ft / 1.52 m in any dimension.

If equipped with a 3-prong, grounded type plug, do not remove the grounding pin from the plug on the power cord.

1. Distilled water is always recommended to fill your fountain. Distilled water is pure and should have no minerals or sediment in it. It will extend the life of the

pump and the time between cleanings. If distilled water is not an option, use filtered water, as water directly from your tap will generally have minerals and

chemicals that can build up and leave behind residue on your fountain.

2. Check the water level regularly to ensure the pump is completely submerged during operation. This is necessary ensure proper cooling of the pump and

prevent overheating. In summer months, or dry, hot climates, water evaporates very quickly, so it may be necessary to check the water level every day. The

rate of water evaporation will also be greater with larger fountains, with more surface area, than smaller fountains.

3. Keep the fountain water and pump clean and clear of debris. If placed under a tree or near vegetation, you may need to scoop out leaves and other debris

every other day. Water treatments that prevent algae growth and mineral deposits are available at your local home & garden stores. Do not use bleach as it

may be harmful to pets and wildlife and may also damage the finish of the fountain.

4. Clean the fountain monthly to prevent mineral deposits and contamination which may clog the pump.

Disconnect the pump from the power source and empty the water from the fountain. Use any gentle household cleanser and a soft brush or cloth to clean

the fountain. Avoid using any harsh chemicals, abrasives or rough scrubbing, as this could damage the finish on your fountain. The frequency of cleaning

may vary depending on the location of your fountain.

5. Use a pre-filter on your pump if available to prevent it from clogging with leaves or other debris.

6. Regular cleaning of the pump will be necessary depending upon the environment in which it is operated. Clean the pump when it is visibly soiled or when a

ASSEMBLY

ASSEMBLY INSTRUCTIONS

ASSEMBLY

INSTRUCTIONS

NOTE: The diagrams shown are for illustrative purposes only and are not to scale

SAFETY

SAFETY INSTRUCTIONS

INSTRUCTIONS

INSTRUCTIONS FOR

CARE

CARE AND

CARE

AND

AND MAINTENANCE

AND

FOR

FOR PUMP

FOR

PUMP

MAINTENANCE