Jandy CPHVLEDS50 Installationshandbuch - Seite 10

Blättern Sie online oder laden Sie pdf Installationshandbuch für Beleuchtungsanlagen Jandy CPHVLEDS50 herunter. Jandy CPHVLEDS50 16 Seiten. Watercolors led lights underwater large and small light
Auch für Jandy CPHVLEDS50: Installationshandbuch (20 seiten)

Seite drucken

Page 10

English

6.2

To Reset to the Beginning of the Color

sequence

Turn the light OFF, wait four (4) to five (5) seconds, then

turn ON, the light will return to the beginning of the color

cycle (Alpine White).

nOTE

If an AquaLink RS control system is being used the

color set can be selected using the indoor controller.

nOTE

To synchronize colors on multiple Jandy Pro Series

WaterColors Light systems wired to separate switches,

perform the above actions on all of their switches

simultaneously. All Jandy Pro Series WaterColors

Lights will synchronize automatically if activated by the

same switch. No other accessories are required.

section 7. Replacing light

Engine (PCB)

WARning

Always disconnect power to the color light at the

circuit breaker before servicing the light. Failure to do

so could result in death or serious injury to installer,

serviceman, pool or spa users or others due to

electrical shock.

Turn off the main electrical switch or circuit

breaker, as well as the switch, which operates the

underwater light.

Be sure to have the following items:

• A new lens gasket, P/N R0451101 for the large

light or P/N R0400501 for the small light.

• A light engine. See Table 2 for specification.

WARning

Replace light engine with the same type. Failure

to replace the light engine with the same type will

damage the light assembly and may cause an

electrical hazard resulting in death or serious injury to

pool or spa users, installers, or others due to electrical

shock, and may also cause damage to property. Be

sure the power is switched OFF before removing or

installing PCB. Allow PCB to cool before replacing.

To remove the light assembly, unscrew the special

pilot screw at the top of the face ring, remove

light assembly from niche and gently place

assembly on the deck. It is not necessary to drain

down the pool. See Figure 6.

Jandy

Pro Series, WaterColors LED Lights

Table 2.

Jandy Pro series

Model

WaterColors

large light

WaterColors

large light

WaterColors

small light

WaterColors

small light

Be sure to keep the special pilot screw from this

underwater light. This screw mounts and electrically

grounds the housing securely to the mounting ring

and wet niche. Failure to use the screw provided could

create an electrical hazard, which could result in death

or serious injury to pool or spa users, installers or

others due to electrical shock.

a. Loosen the Phillips head screws (six (6) for

b. Remove the bottom clamp, the face ring

a. 12V Small Light Engine (PCB) Replacement

Installation Manual

light specifications

Fixture

Voltage

12 Volt AC

120 Volt AC

12 Volt AC

120 Volt AC

WARning

Pool Clamp Removal.

small light, eight (8) for large light) to allow

the bottom clamp to be removed from the face

ring assembly. Do not remove the screws or the

retaining rings. The retaining rings prevent the

screws from falling free from the bottom clamp

and also aid in ease of assembly.

assembly, the glass lens, and the gasket from the

fixture. Remove the gasket from the lens. Refer

to Section 9, Exploded View and Replacement

Parts.

Light Engine Replacement

1. Remove two (2) nuts and two (2) washers.

2. Unplug the quick disconnect terminals from

the light engine.

3. Remove the light engine from the light

fixture.

4. Place new light engine into the fixture with

the orientation shown in Figure 7.

Secure the light engine with one (1) nylon

washer and one (1) nut. Torque to 12 in-lbs.

6. Place a nylon washer on the other stud and

place the green ground wire terminal on the

nylon washer and secure both with the nut.

Torque to 12 in-lbs.

light Engine (PCB)

Part number

R0474000

R0474100

R0473900