Empire FAW-40-1SPP Benutzer- und Installationshandbuch - Seite 11

Blättern Sie online oder laden Sie pdf Benutzer- und Installationshandbuch für Furnace Empire FAW-40-1SPP herunter. Empire FAW-40-1SPP 18 Seiten. Fan type vented wall furnace

Seite drucken

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ﬁre or explosion may result

A. This appliance has a pilot which must be lighted by

hand. When lighting the pilot, follow these instructions

exactly.

B. BEFORE LIGHTING smell all around the appliance

area for gas. Be sure to smell next to the ﬂoor because

some gas is heavier than air and will settle on the

ﬂoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch;

do not use any phone in your building.

• Immediately call your gas supplier from a neighbor's

phone. Follow the gas supplier's instructions.

1. S T O P !

R e a d t h e s a f e t y i n f o r m a t i o n

above.

2. Set the thermostat to lowest setting.

3. Turn off all electric power to the appliance.

4. Remove control access panel (lower front

panel).

5. Turn gas control knob clockwise

to "OFF."

6. Wait ten (10) minutes

Then smell for gas, including near the ﬂoor. If you smell

gas, STOP! Follow "B" in the safety information above.

If you don't smell gas, go to the next step.

7. Remove the pilot access cover located on the

combustion chamber.

8. Find pilot - follow metal tube

from gas control. The pilot is

located between the two burner

1. Set the thermostat to lowest setting.

2. Turn off all electric power to appliance if

service is to be performed .

3. Remove

control

12427-5-0806

STANDING PILOT MODEL

causing property damage, personal injury or loss of life.

LIGHTING INSTRUCTIONS

to clear out any gas.

TO TURN OFF GAS TO APPLIANCE

access panel

(lower front

• If you cannot reach your gas supplier, call the ﬁre

department.

C. Use only your hand to push in or turn the gas control

knob. Never use tools. If the knob will not push in or

turn by hand, don't try to repair it; call a qualiﬁed

service technician. Force or attempted repair may

result in a ﬁre or explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualiﬁed service technician

to inspect the appliance and to replace any part of

the control system and any gas control which has

been under water.

tubes behind the pilot access cover.

9. Tu r n g a s c o n t ro l k n o b c o u n t e rc l o c k w i s e

to "PILOT."

10. Push and hold red reset button down com-

pletely and repeatedly push the ignitor button until the

pilot burner is lit. Pilot may also be lit with a match.

Continue to hold the red reset button down for about

one (1) minute after the pilot is lit. Release button and

it will pop back up. Pilot should remain lit. If it goes

out, repeat steps 5 through 10.

• If button does not pop up when released, stop and

immediately call a qualiﬁed service technician or

gas supplier.

• If the pilot will not stay lit after several tries,

turn the gas control knob to "OFF" and call your

service technician or gas supplier.

11. Replace pilot access cover.

12. Turn gas control knob counterclockwise

to "ON."

13. Replace control access panel (lower front

panel).

14. Turn on all electric power to the appliance.

15. Set thermostat to desired setting.

panel).

4. Push in gas control knob slightly and turn

clockwise

to "OFF." Do not force.

5. Replace control

panel).

access panel

(lower front

Page 11