Avaya 1110 Erste Schritte - Seite 2

Blättern Sie online oder laden Sie pdf Erste Schritte für IP-Telefon Avaya 1110 herunter. Avaya 1110 2 Seiten.

Seite drucken

Avaya 1110 IP Deskphone installation

Caution: Your Avaya 1110 IP Deskphone is shipped with the stand locked in

position. To release the phone from the stand, press the wall-mount lever (see

Figure 3) and gently tilt the phone up from the stand a little. When you're sure the

phone is released from the stand, press the tilt lever and tilt the phone up from the

stand all the way.

Step 1: Remove the stand cover. Pull upward on the center catch (see Figure 4) and remove

the stand cover from the stand base. The cable routing tracks are now accessible in the stand

base (see Figure 5).

Step 2: Connect the AC power adapter (optional). Connect the AC power adapter (not

supplied) to the AC adapter jack in the bottom of the phone (see Figure 2). Form a small bend

in the cable and thread the adapter cord through the channel in the stand base. Plug the AC

power adapter into the nearest AC power outlet.

Note: Your Avaya 1110 IP Deskphone supports both AC power and Power over Ethernet

(PoE), including IEEE 802.3af standard power. To use AC power, use only the Avaya-

approved AC power adapter (RoHS Global Power Supply NTYS17xxE6), which can be

ordered separately. To use Power over Ethernet (PoE) power, your connected LAN must

support PoE; when using PoE, an AC power adapter is not required.

Step 3: Install the handset. Plug the end of the handset cord with the short straight section

Avaya 1110 IP Deskphone installation

into the handset. Plug the end of the handset cord with the long straight section into the

handset jack in the back of the phone (see Figure 2) marked with the symbol

bend in the cord, and then thread it through the channel in the stand base marked with the

symbol

so that it exits in the handset cord channel on the right -hand side of the stand base

(see Figure 4).

Step 4: Install the LAN Ethernet cable. Plug one end of the supplied LAN Ethernet cable into

the LAN Ethernet port on the back of your phone (see Figure 2) marked with the symbol

and thread the cable through the channel in the stand base marked with the symbol

Connect the other end of the cable to your LAN Ethernet connection.

Step 5: Install the PC Ethernet cable (optional). If you are connecting your PC Ethernet

through the phone, plug one end of the PC Ethernet cable (not supplied) into the PC Ethernet

port on the back of your phone (see Figure 2) marked with the symbol

through the channel in the stand base marked with the symbol

LAN port on the back of your PC.

Step 6: Wall-mount your phone (optional). Your Avaya 1110 IP Deskphone can be mounted

either by: (Method A) using the mounting holes on the bottom of the phone stand, or (Method

B) using a traditional-style wall-mount box with RJ-45 connector and 15-cm (6-inch) CAT5e

cable (not supplied).

Complete steps 1-5, as needed, before you wall-mount your phone:

Method A: Using the stand cover (part removed in step 1), mark the wall-mount holes by

pressing the bottom of the stand cover firmly against the wall in the location where you wish to

install the phone. Four small pins on the bottom of the stand cover make marks on the wall.

Use the marks as a guideline for installing the wall-mount screws (not supplied). Install the

screws so that they protrude 3 mm (1/8 inch) from the wall, and then position the phone stand

mounting holes (as shown in Figure 5, Method A) over the screw heads. You may need to

remove the phone from the wall to adjust the lower screws. When the lower screws fit snugly,

tighten the top screws.

Method B: Attach the 15-cm (6-inch) CAT5e cable (not supplied), position the phone stand

mounting holes (shown in Figure 5, Method B) over the mounting rivets, push the phone onto

the rivets, and down to lock into position.

Step 7: Replace the stand cover. Ensure that all cables are neatly routed and press the

stand cover into place until you hear an audible click.

Avaya 1110 IP Deskphone installation and controls

Step 8: Put the phone in the wall-mount position. If you wall-mounted your phone, put it in

. Form a small

the wall-mount position by pressing the tilt lever and pushing the phone towards the stand until

nearly parallel with the stand. Release the tilt lever and continue to gently press the phone

towards the stand until you hear an audible click (from the wall mount lever). Ensure the phone

is securely locked in position.

Avaya 1110 IP Deskphone controls:

Controlling volume

Press the up or down volume control key while using your handset or speaker to adjust the

volume of the associated device.

Answering a call

Lift the handset to answer a ringing call.

, and thread the cable

(

Making a call with the handset

. Plug the other end into the

(

Lift the handset and enter the phone number on the dialpad. When your call is complete, press

the Goodbye key or return the handset to the cradle.

Making a call using on-hook dialing

Press the Line key and enter the phone number on the dialpad. When your call is answered,

lift the handset. When your call is complete, press the Goodbye key or return the handset to

the cradle.

Placing a call on Hold

While on a call, press the Hold key to place your caller on hold. To retrieve your caller on hold,

press the Line key.

Setting the contrast

To adjust the display contrast, press the Services key, select Telephone Options, and select

Contrast Adjustment. Use the up/down arrow keys or up/down soft keys to change the

setting.

Setting the language

To select the language used by the local menus, press the Services key twice quickly to open

the local menu. Select 1. Preferences, select 2. Language, and use the up/down arrow keys

to choose the language.

Note: Use the Telephone Options menu to select the language used by server-based

features. See the Avaya 1110 IP Deskphone User Guide NN43110-101 for more information.