Jandy Infinite WaterColors IWCP50W100 Installations- und Betriebshandbuch - Seite 4
Blättern Sie online oder laden Sie pdf Installations- und Betriebshandbuch für Controller Jandy Infinite WaterColors IWCP50W100 herunter. Jandy Infinite WaterColors IWCP50W100 12 Seiten. Led lighting
Auch für Jandy Infinite WaterColors IWCP50W100: Installations- und Betriebshandbuch (12 seiten), Handbuch (2 seiten)
Seite drucken
ENGLISH
1.2
Landscape Lighting Instructions
THIS SECTION INCLUDES INSTRUCTIONS,
PRECAUTIONS AND WARNINGS APPLICABLE TO
LANDSCAPE LIGHTING APPLICATIONS. FOLLOW
ALL REQUIREMENTS OF THIS SECTION WHEN LIGHT
CONTROLLER IS USED IN LANSDCAPE LIGHTING
APPLICATIONS. .
CAUTION: For use only on a branch circuit protected by
a ground fault circuit interrupter (GFCI), Class A GFCI in
Canada.
R I S K
O F
E L E C T R I C A L
Install Install power unit 5 feet (1.5 m) or more from a
pool or spa and 10 feet (3.05 m) or more from a fountain.
Where the power unit is installed within 10 feet (3.05 m)
of a pool or spa connect power unit to a GFCI protected
branch circuit. In Canada, do not mount power supply or
landscape luminaires within 3 m (10 feet) of a swimming
pool or spa or fountain.
THIS DEVICE IS ACCEPTED AS A COMPONENT OF
A LANDSCAPE LIGHTING SYSTEM WHERE THE
SUITABILITY OF THE COMBINATION SHALL BE
DETERMINED BY CSA OR LOCAL INSPECTION
AUTHORITIES HAVING JURISDICTION
-IN CANADA, LANDSCAPE LIGHTING POWER SUPPLIES
ARE FOR OUTDOOR USE ONLY. MOUNT AT LEAST 30 CM
ABOVE GROUND.
-THIS DEVICE IS CERTIFIED FOR USE WITH LANDSCAPE
LIGHTING SYSTEMS. THIS DEVICE IS ACCEPTED AS
A COMPONENT OF A LANDSCAPE LIGHTING SYSTEM
WHERE THE SUITABILITY OF THE COMBINATION SHALL
BE DETERMINED BY CSA OR LOCAL INSPECTION AU-
THORITIES HAVING JURISDICTION.
-DO NOT CONNECT TWO OR MORE POWER SUPPLIES
IN PARALLEL.
-LANDSCAPE LIGHTING SYSTEMS ARE FOR OUTDOOR
USE ONLY. NOT FOR USE IN DWELLING UNITS.
1.3
Specifications
Power Supply
Input:
120VAC, 60 Hz, 2.75A
Output:
14 VAC, 60 Hz, max 300W
Enclosure
Type 3RX
Knockouts
10 total 1/2" - 3/4" combination
Page 4
WARNING
S H O C K
Jandy
Infinite WaterColors
LED Light Controller
®
™
Aqualink will support control of up to 4 Infinte
WaterColors Light Controllers and each controller will
support communication with up to 16 lights. Ensure the
combined light wattage does not exceed 240W
per controller.
The Infinite WaterColors LED Light Controller should not
be considered suitable for use as service equipment.
Therefore, it is required to have the appropriate means
of disconnection, circuit isolation, and/or branch circuit
protection installed upstream of the power center.
Section 2. System Overview
This manual provides installation and basic operational
instructions for the Jandy Infinite WaterColors LED
Light Controller. The Infinite WaterColors LED Light
Controller includes a 300W transformer specifically
designed to supply 14 volts to pool/spa lights,
submersible fixtures, and outdoor garden lights. The
Infinite WaterColors LED Light Controller is capable
of communicating with the low voltage lights and
automation systems. The built-in circuit protection will
disconnect power to the transformer in case of defect
or overload. These transformers are suitable for direct
connection to underwater pool, spa, and landscape lights.
Read the installation and operation instructions
completely before proceeding with the installation.
Keep this manual in a safe place for future reference
when inspecting or servicing the Infinite WaterColors
LED Light Controller.
Before starting, check that you have the correct parts as
indicated below. If any parts are missing or incorrect,
please call your local distributor or technical support at
1-800-822-7933 for assistance.
2.1
Package Contents
Jandy Infinite WaterColors LED Light Controller
1- Enclosure and PIB
2- Upper mounting bracket
3- Lower mounting bracket
4- 20 FT RS-485 Cable
|
Installation & Operation Manual
WARNING