Gardena 4066 Benutzerhandbuch - Seite 3

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Rasenmäher Gardena 4066 herunter. Gardena 4066 15 Seiten. Electric lawn rake
Auch für Gardena 4066: Betriebsanleitung (12 seiten), Betriebsanleitung (9 seiten), Benutzerhandbuch (15 seiten), Benutzerhandbuch (15 seiten), Benutzerhandbuch (9 seiten), Benutzerhandbuch (9 seiten)

Seite drucken

DANGER! Electric shock!

Keep supply flexible cord

away from tines.

1. General

This annex presents safe operating practices for all

machine types covered by this standard.

IMPORTANT!

READ CAREFULLY BEFORE USE.

KEEP FOR FUTURE REFERENCE.

2. Safe operating practices for scarifiers / aerators

2.1 Training

a) Read the instructions carefully. Be familiar with the

controls and the correct use of the equipment.

b) Never allow children or people unfamiliar with

these instructions to use the machine. Local regu-

lations can restrict the age of the operator.

c) Keep in mind that the operator or user is respon-

sible for accidents or hazards occurring to other

people or their property.

2.2 Preparation

a) Wear ear protection and safety glasses at all times

while operating the machine.

b) Before use check the supply and extension cord

for signs of damage or aging. If the cord becomes

damaged during use, disconnect the cord from the

supply immediately.

DO NOT TOUCH THE CORD BEFORE

DISCONNECTING THE SUPPLY.

Do not use the machine if the cord is damaged or

worn.

c) While operating the machine always wear substan-

tial footwear and long trousers. Do not operate the

machine when barefoot or wearing open sandals.

Avoid wearing clothing that is loose fitting or that

has hanging cords or ties.

d) Thoroughly inspect the area where the equipment

is to be used and remove all objects which can be

thrown by the machine.

e) Operate the machine in a recommended position

and only on a firm, level surface.

f) Do not operate the machine on a paved or gravel

surface where ejected material could cause injury.

g) Before starting the machine, check that all screws,

nuts, bolts, and other fasteners are properly

secured and that guards and screens in place.

Replace damaged or unreadable labels.

h) Never operate the machine while people,

especially children, or pets are nearby.

2.3 Operation

a) Operate the machine only in daylight or in good

artificial light.

b) Avoid operating the machine in wet grass.

c) Always be sure of your footing at all times, espe-

cially on slopes.

WARNING!

Beware of sharp tines!

Keep fingers and toes away.

Remove plug from mains before mainte-

nance, adjusting, cleaning or if the cord is

entangled or damaged. Tines continue to

rotate after the motor is switched off.

d) Walk, never run.

e) Mow across the face of slopes, never up and

down.

f) Exercise extreme caution when changing direction

on slopes.

g) Do not scarify or aerate excessively steep slopes.

h) Use extreme caution when reversing or pulling the

machine towards you.

i) Stop the tines if the machine has to be tilted for

transportation when crossing surfaces other than

grass, and when transporting the machine to and

from the area to be used.

j) Never operate the machine with defective guards

or shields, or without safety devices, for example

deflectors and/or grass collector, in place.

k) Switch on the motor carefully according to instruc-

tions and with feet well away from the tines.

l) Keep supply and extension cord away from tines.

m) Do not tilt machine when switching on the motor,

except if the machine has to be tilted for starting.

In this case, do not tilt it more than absolutely nec-

essary and lift only the part which is away from the

operator. Always ensure that both hands are in the

operating position before returning the machine to

the ground.

n) Do not transport the machine while the power

source is running.

o) Do not put hands or feet near or under rotating

parts. Keep clear of the discharge opening at all

times.

p) Stop the machine, and remove plug from the

socket. Make sure that all moving parts have

come to a complete stop:

1) whenever you leave the machine,

2) before clearing blockages or unclogging chute,

3) before checking, cleaning or working on the

machine,

4) after striking a foreign object. Inspect the

machine for damage and make repairs before

restarting and operating the machine;

if the machine starts to vibrate abnormally

(check immediately):

5) inspect for damage,

6) replace or repair any damaged parts,

7) check for and tighten any loose parts.

2.4 Maintenance and storage

a) Keep all nuts, bolts and screws tight to be sure the

equipment is in safe working condition.

b) Check the debris collector frequently for wear or

deterioration.

c) Replace worn or damaged parts for safety.