KitchenAid YKEBC107KS0 Einbauanleitung - Seite 3

Blättern Sie online oder laden Sie pdf Einbauanleitung für Backofen KitchenAid YKEBC107KS0 herunter. KitchenAid YKEBC107KS0 5 Seiten. 30" electric built-in single and double ovens

Seite drucken

_fcodes p ermit a ndaseparate g rounding

wireis used, i t isrecommended thata

qualified

e lectrician

determine

that the

grounding

path and wire gauge are in

accordance

with _oca_codes.

Do Not ground to a gas pipe.

Check with

a qualified

electrician

if you are

not sure oven is proper_y grounded.

Do Not have a fuse in the neutral

grounding

circuit.

This oven must be connected

to a grounded

metal

permanent

wiring

system.

Oven must be connected to the proper

eUectdcaU voffage and frequency as specified

on the model/serial rating plate. (The

model/serial rating plate is located on the

oven door or on the oven frame.}

[_ Models rated from 7.3 to 9.6 kW at 240

volts (5,5 to 7,2 kW at 208 volts} require a

separate @-ampere circuit. Models rated

at 7.2 kW and below at 240 volts (5.4 kW

and below at 208 volts} require a separate

30°ampere circuit.

[_ A timeodelay fuse or circuit breaker is

recommended.

[_ Connect directly to the fused disconnect

(or circuit breaker box) through flexible,

armored or non-metallic sheathed, copper

cable (with grounding wire).

[_ Flexible armored cable from appliance

should be connected directly to junction

box.

[_ Fuse both sides of the line.

[_ A U.L.-listed conduit connector must be

provided at the junction box.

[_ Do Not cut the conduit.

Wire sizes and connections must conform

with the rating of the appliance and to the

requirements of the National Electrical Code,

ANSVNFPA 70 -- latest edition _, or Canadian

Electrical Code, C22.1-1982 and C22.2 No.

01982 (or latest edition) *_ and all local codes

and ordinances.

if the house has aluminum wiring, follow the

procedure below.

a.) Connect the aluminum wiring to the

copper wire using special connectors

designed and Underwriters Laboratories°

listed for joining copper to aluminum.

Follow the electrical connector

manufacturer's recommended procedure.

b.) Aluminum/copper

connection must

conform with local codes and industry-

accepted wiring practice.

Copies

of the standards

listed

may be obtained

from:

National

Fire Protection

Association

Ratterymamh

Park

Quincy,

Massachusetts

02269

** CSA International

8501 East Pleasant

Valley

Road

Cleveland,

Ohio

44131=5575

Grasp oven

frame to lift

oven,

power

suppBy cable

]

Remove

shipping

feet.

Use screws to attach

oven to cabinet.

Reattach

side

trim.

Remove

trim screws.

Remove side

trim.

_J_

Grasp oven

frame to lift

oven.

Use screws to

attach

oven to

cabinet.

[eattach

side

trim.

Remove side

trim.

Preparation

Excessive

Weight Hazard

Use two or more people to move and

install oven.

Failure to follow this instruction

can

result in back or other injury.

Important: Use both hands to remove oven

doors.

Do Not use handle or any portion of the front

frame or trim for lifting.

Before moving oven across floor, check that

oven is on shipping base or slide oven onto

cardboard or hardboard.

Do Not remove shipping feet at the front lower

corners of oven,

Do Not remove

shipping

feet.

m Turn power supply off. Move oven

close to final position.

, Remove and discard shipping materials,

tape and protective film from the oven.

Do Not remove shipping base or

shipping feet at the front _ower corners

of oven. The shipping feet will protect

the _ower oven trim until oven is

inserted into cabinet.

, Remove and set aside racks and other

parts from inside oven.

Remove

oven

door.

power

supply cable

Remove

shipping

feet.

Remove trim

$srews.

Remove

oven

doors,

Replace

oven

doe!

match on the

hinge

in locked

position

door

free

to open

and

latch

on the

hinge

in unlocked

position

= door

ready

for removal

Remove trim screw.

Puff trim out,

Pull top of trim

down,

m Completely open oven door. in both

back corners of the door you will see door

latches in the locked position. Rotate both

latches forward to the unlocked position.

Grasp outside edges of door with both hands.

Begin closing door, at the moment the door

stops closing, lift and puii door toward you.

Set door aside on a protective surface.

Remove trim screws attaching right

and left side trim to oven. Grasp the bottom

end of trim and pull away from oven. Slide

top end of trim downward to remove trim

from oven. Take care not to scratch other

surfaces with ends of trim. Set trim and

screws aside on protected surface.

Page 2