Gardena 7869 Betriebsanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Water Pump Gardena 7869 herunter. Gardena 7869 6 Seiten. Submersible pump for pond filter or stream

Seite drucken

pump checked by our GARDENA Service Centre or by an

authorised electrician.

Check line voltage

Check line voltage. Data indicated on the type plate must match

technical data of the mains supply.

Do not operate pump

The pump must not be operated when there are people in the

when there are people

water.

in the water

Swimming pools

Swimming pools and garden ponds should be designed accord-

and garden ponds

ing to international and national design regulations. Please

consult a professional electrician.

Do not use power cable

Do not use the power cable to carry the pump or to pull the plug

to carry the pump

out of the socket. Protect the power cable from heat, oil and

sharp edges.

Disconnect plug

Please unplug the pump after operation and before carrying out

any maintenance works.

Temperature of the liquid

The temperature of the liquid used must not be below 4 °C or

used

above 35 °C.

Wear and reduced

Sand and other abrasive substances in the liquid cause in-

output

creased wear and reduce the output of the pump.

Observe local noise

Please observe the local noise prevention regulations.

prevention regulations

Operation

The universal fitting provides you with various possibilities

G 3 /4

to fit a hose:

➔ Connection via graduated nipple of

25 mm (1")- or

32 mm (5 /4")- or

G 1

38 mm (1 1/ 2 ")- hoses

➔ Connection via GARDENA Water hose-Plug-in-system

5 /4"

fittings of

13 mm (1/ 2 ")- or

1 1/ 2 "

16 mm (5 / 8 ")- or

19 mm (3 /4")- hoses

Recommendation :

Fix 38 mm (1 1/ 2 ")-, 32 mm (5 /4")- and 25 mm (1")-hoses

additionally with a hose clip.

Cut off the parts of the universal fitting that you do not need

with a saw.

Fitting the universal

1. Push the sleeve nut over the universal connector.

connector

2. Place the sealing ring in the sleeve nut.

3. Screw the universal adapter and sleeve nut onto the pressure

joints of the pump.

Positioning the pump

Position the pump on a firm base so that it is at least 20 cm

immersed in water.

Pay attention to

Please note the maximum submersion depth (see "Technical Data").

minimum water depth

Starting the pump

Connect the power cable to a 230 V AC socket.

Caution! Pump will start running immediately!

Avoid dry operation

Avoid dry operation of the pump as dry running will produce

undesirable heat and destroy the pump.

System Extensions – Product Recommendations

Operating an external filter

To clean your pond you can connect an external filter such as the

GARDENA Pond Filter

GARDENA Pond Filter with UVC-light

For this purpose use a hose in order to connect the Pump

for Filters and Streams with the external filter.

Please observe the information on safety in the relevant

operating instructions!

Operating a stream

The pump has been designed for streams and waterfalls:

Large streams and waterfalls

➔ Connect a 38 mm (1 1/ 2 ") GARDENA Pond Hose,

Art. No. 7898, and run it to the source of your stream.

Smaller streams

➔ Connect hoses with a smaller diameter correspondingly e.g.:

32 mm (5 /4")-GARDENA Pond Hose, Art. No. 7897

25 mm (1")-GARDENA Pond Hose, Art. No. 7896.

Care Instructions

Cleaning the pump

If you use your pump frequently in dirty water you should clean

your pump as follows:

1. Remove the mains plug.

2. Take the pump out of the water.

3. Rinse the housing of the pump thoroughly with water.

If necessary, also direct the water into the pressure outlet.

4. Put the pump back into your pond or stream.

Information: Do not use any hard objects or strong detergents!

Art. No. 7904

Art. No. 7905